Q.2// 66 Select a tension diagonal member of A36 steel [ Fu= 58 ksi ]. The axial tension is 50k dead load and 16 k live load and the member is 13 ft long. Assume 3/4" -diameter bolts will be located on a single gage line. Assume the preferable limit on slenderness ratio L/r is 280: - Select the lightest single angle member. Select the lightest double angle member having legs separated by 1/4" Gusset plates

Q.2// 66 Select a tension diagonal member of A36 steel [ Fu= 58 ksi ]. The axial tension is 50k dead load and 16 k live load and the member is 13 ft long. Assume 3/4" -diameter bolts will be located on a single gage line. Assume the preferable limit on slenderness ratio L/r is 280: - Select the lightest single angle member. Select the lightest double angle member having legs separated by 1/4" Gusset plates

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The tension member shown is a PL 5/8 x 10, and the steel is A36. The bolts are 7/8-inch in diameter. a. Determine the design strength for LRFD. b. Determine the allowable strength for ASD. 2" 2" -|-|- |-|-|- -| 3 die einheitliche O O O OO O
The tension member shown in Figure P3.2-5 is a PL 1/2 x 8 of A36 steel. The member is connected to a gusset plate with-11/8 inch- diameter bolts. It is subjected to the dead and live loads shown. Does this member have enough strength? Assume that Ae = An. оооо D=95t L=9k PL ½x8
The tension member shown in the figure below is a ¹/2 x 10 plate of A36 steel: Fy = 36 ksi, Fu = 58 ksi. The connection is with 9/8-inch-diameter bolts. -→| 20 |einetein | 21 | 6 spaces @2" t = 1/2 in. Compute the nominal strength based on the net section. (Express your answer to three significant figures.) P₁ = kips
A double-angle shape, 2L8×8×%, is connected to a %-inch gusset plate as shown in Figure 3. Determine the maximum total service load that can be applied if the ratio of dead load to live load is 0.5. The bolts are 1-inch-diameter, Group B bearing type bolts. A572 Grade 50 steel is used for the angle, and A36 steel is used for the gusset plate. Threads are not excluded from the shear plane. Assume that block shear failure is not going to happen. T 2" 3" 3" 3" 00 -OO 00 -oo - t = 5/8" Figure 3
2. A single-angle tension member, an L3x3 x3/8, is connected to a gusset plate with 22mm- diameter bolts as shown in the figure. A36 steel is used. The service loads are 155KN dead load and 66 kN live load. Investigate this member for compliance with the NSCP 2015 Specification. Assume that the effective net area is 85% of the computed net area. Consider yielding of the gross section and fracture of the net section. Neglect block shear. a. Use LRFD. b. Use ASD L3½x 3/2 x% Section
Select the lightest C6 channel shape to be used as a 12 ft long tension member to resist the following service loads, PD = 20 k and P₁ = 32 k. The member will be con- nected by a transverse weld at the end of the channel only. Use A36 Grade 36 steel with F = 58 ksi. (Ans. C6 × 10.5 LRFD and ASD)
A double-angle shape, 2L7 3 4 3 3⁄8, is used as a tension member. The twoangles are connected to a gusset plate with 7⁄8-inch-diameter bolts throughthe 7-inch legs, as shown in Figure P3.4-5. A572 Grade 50 steel is used.a. Compute the design strength.b. Compute the allowable strength.
PLEASE DOUBLE CHECK YOUR ANSWER Determine the maximum factored load that can be applied to the Tension member shown. The angle is ASTM A36. The diameter of the bolts is 1-in. CIVIL ENGINEERING STEEL DESIGN W12 x 16 4,-0.220 in -3.99 in 1=+=+=+= 3 in 3 in 3 in
1. The tension member shown in Figure 3.4-2 is a PL 58 x 10, and the steel is A36. The bolts are 3/4-inch in diameter. a. Draw the different potential failure lines. b. Compute the effective net area. 22" 2½" 2" 4 3" *₁ 3" ✓ 2" 2. A double-channel shape, 2C10 x 20 steel, Fy = 50 ksi and Fu = 70 ksi, is used for a built-up tension member as shown in the figure. The holes are for 12-inch-diameter bolts. PNA a. Determine the design strength for LRFD. b. Determine the allowable strength for ASD. YD Shape A 2" 2" -X Area, Depth, d | 3²²-|-1 3²² | 00 "There is no elevator to success, you have to take the stairs." - Zig Ziglar God bless. Ⓒ O O O Web Thickness, tw in. in. O 4" C10-30 x25 x20 5.87 10.0 10 0.379 % x15.3 4.48 10.0 10 0.240 4 4" Table 1-5 C-Shapes Dimensions Flange Width, b₁ 2 in. in. in.2 in. C15x50 14.7 15.0 15 0.716 1168 3.72 3% 0.650 % x40 11.8 15.0 15 0.520 x33.9 10.0 15.0 15 0.400 % 14 3.52 32 0.650 % %/16 3.40 3% 0.650 % C12-30 8.81 12.0 12 0.510 4 3.17 3% x25 7.34 12.0 12…
2. A MC230x35.6 connected to a gusset plate with 24 mm diameter bolts as shown. The steel is A572M grade 345. If the member is subjected to dead and live load only, what is the total service load capacity if the live-to-dead load ratio is 3 ? 50+ 65 65 50 mmt 50 15 65 mm O MC 230 x 35.6
The tension member shown in Figure 3.4-2 is a PL 5/8 x 10, and the steel is A36. The bolts are 7/8-inch in diameter. a. Determine the design strength for LRFD. b. Determine the allowable strength for ASD. | 2" +|+| in seinefrinehich 9 оо SO