Select the lightest C6 channel shape to be used as a 12 ft long tension member toresist the following service loads, PD = 20 k and P₁ = 32 k. The member will be con-nected by a transverse weld at the end of the channel only. Use A36 Grade 36 steelwith F = 58 ksi. (Ans. C6 × 10.5 LRFD and ASD)

Given:- The length of the tension member = 12 ft The magnitude of the dead load = PD = 20 k The…

Select the lightest C6 channel shape to be used as a 12 ft long tension member to resist the following service loads, PD = 20 k and PL = 32 k. The member will be con- nected by a transverse weld at the end of the channel only. Use A36 Grade 36 steel with F₁ = 58 ksi. (Ans. C6 X 10.5 LRFD and ASD)

Select the lightest C6 channel shape to be used as a 12 ft long tension member to resist the following service loads, PD = 20 k and PL = 32 k. The member will be con- nected by a transverse weld at the end of the channel only. Use A36 Grade 36 steel with F₁ = 58 ksi. (Ans. C6 X 10.5 LRFD and ASD)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 1. Determine the allowable load Pa based on bearing at bolt holes. (ASD) 2. Determine the ultimate…

A: Given:- Thickness of plate, t=16 mmDiameter of bolts, d=22 mmNumber of bolts, n=6S1=40 mmS2=80…

Q: Design the size and length of Fillet weld for the lap joint shown below, Use SMAW E70XX process,…

A: Live load, Dead load, Thickness of plate, ElectrodeTo find: Size and length of fillet weld for the…

Q: The welded girder shown in the accompanying illustration has an external shear VD = 300 k and VL =…

A: VD=300 kVL=350 k

Q: 1.A tension member is 25 mm thick plate as shown. The bolts are 20 mm. diameter high-strength bolts.…

A: Plate 130 mm x 25 mmbolt diameter, db = 20 mmA36 grade of steel:fy = 250 MPafy = 400 MPaTo find:a)…

Q: PROBLEM 9.9 9.10 In the bolted connection of Figure 9.12, assume that the bolts are in. in diameter…

Q: Determine the tensile strength of the welded A992 WT4×20. WT4 × 20 PL - Transverse weld

A: Given:- The steel section used = WT 4×20 The steel used = A992 To determine:- The tensile strength…

Q: 4. An UPE 300 is to be used as a tension member and it is bolted to a 10mm thick gusset plate with…

A: Tension member UPE 300 bolted connection. Fy = 275 N/mm2 Fu = 430 N/mm2 Ag= 5660 mm2 tw= 9.5 mm

Q: o normal temperatures but wet in-service conditions. Assume =0.95 and the geometry factor is CA=1.…

A: 1 Area of the plate Ag Ag = 4×10 = 40 in2for A36 grade steel fy =36000…

Q: Apply AISC LRFD procedure to design a welded connection for a vertical truss member L127x76x9.5 with…

Q: The connection of the drawbar and tie plate combination given below will be made by welding with two…

A: Welded connections: The point at which two or more pieces of metal are joined together is known as…

Q: A riveted connection is shown in the figure 3.26. A 25 mm diameter A 502, grade 2 rivets are used. A…

A: To compute:Tensile strength when shear stress of rivet governsTensile strength when bearing stress…

Q: A PL 38 x 6 tension member is welded to a gusset plate as shown in figure. The steel is A36. PL % ×…

A: Note:- Hi! Thank you for the question, As per the honor code, we are allowed to answer three…

Q: Determine the load-carrying capacity of the 2 PL 5/16 x 3 tension member shown based on the limit…

Q: The PL 18 x 1/2 as shown below are connected to PL 50 x 1/2 in with longitudinal SMAW fillet welds…

A: PL 18 X 1/2 connected to PL 50 X 1/2 Fillet weld 7/15 in fy = 50 ksifu = 65 ksiElectrode = E70

Q: Material Strengths: Fy= 248 MPa, Fu= 400 MPa Method: Use ASD. A single angle L203X152X19 is welded…

Q: he bolt is made of a material havin llowable shearing stress of 55.44 M

A: Given:- Allowable tensile stress=140.44MPa Allowable shearing stress=55.44MPa Axial load=17kN…

Q: A 21419x2 (3/8 in.SEPARATIOV), ASTM A36 „HAs ONE LINE OF &)孝n AND 25 is 25 O LENGTH. DIAMETER BOLTS…

Q: 4. An A992 WF steel section is used for the tension member shown in the figure. The bolts are 20mm…

A: A W16x67 is given , we need to find out a. The nominal strength based on gross section yielding.b.…

Q: Problem 7: The load that will be applied to the connection shown has a live load - to - dead load…

A: Note:- Hi! Thank you for the question, As per the honor code, we are allowed to answer three…

Q: he double I-beam is fabricated by welding the three plates together as shown. Part A 50 mm 75 mm 20…

A: Shearing stress is defined as a type of stress that acts coplanar with the cross section of a…

Q: A tension plate shown below is used to support suspended load "T". Gusset Plate- Fy = 248 MPa Fu =…

A: Given;

Q: A 6x6x9/16 angle as shown is subjected to tensile load and is to be welded with 1/4" weld (EXX of…

A: Note- Since we answer one question at a time so we will answer the first one. Please resubmit…

Q: A channel C250x37 mm section is welded to a 9 mm gusset plate. Welding is not permitted on the back…

A: Slot Weld : Slot weld is used to attach flat plates using one or more holes in the top part. To fuse…

Q: Compute the maximum acceptable tensile SERVICE LOAD that may act on a single tee section that is…

A: Answer In order to calculate the minimum acceptable tensile service load we need to first find the…

Q: 5-5: For the welded 1"x8" flat plate tension member shown, determine the design tensile capacity…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: Governing Ultimate Tensile Capacity based on Yielding of gross section

A: Gross area Ag=11.2 in2Yield stress Fy=50 ksiUltiate stress Fu=65 ksiy¯=3 inLength of weld L=12…

Q: The tension member is a PL 1⁄2 × 6. It is connected to a 3⁄8-inch-thick gusset plate with…

A: The given connection with dimensions as follows :

Q: The splice plates shown in Figure 2 are 1/2-inch-thick. How many %-inch-diameter, Group B bolts are…

A: Nominal bolt area is 'Ab'

Q: The A36 tension member is connected with 6- 16 mm diameter bolt. The member is made of Plate PL…

Q: A plate 400 x 12 mm is to be connected to a plate of the same width and thickness by 34 mm diameter…

Q: A single plate tension member (200 mm x 10 mm) is made of 300W Steel. The member is connected…

Q: Problem # 6.0 For the tension member shown, compute the tensile design strength. Weld -6" PL 4X6 A36…

A: The tension member is given as To find:- Tensile design strength

Q: Consider the connection is welded with 7/16 in. welds with FEXX =70 ksi as shown. The channel…

Q: 6) Calculate the shear lag reduction factor, u, for the spliced W-shape tension member shown. Hint:…

Q: For the tension member shown, compute the following. a. The tensile design strength. b. The…

Q: Situation 2: A WT 8x13 of A992 steel is used as a tension member, The connection is with 7/8-in,…

A: WT 8×13 of A992 Diameter = 78inch Fy=50 ksi Fu = 65 ksi Ubs = 1.0

Q: the allowable tensile load on the members and weldlength and overlap length of

Q: A tension member consists of a double angle section with long legs back to back. The angles are…

Question

Select the lightest C6 channel shape to be used as a 12 ft long tension member to
resist the following service loads, PD = 20 k and P₁ = 32 k. The member will be con-
nected by a transverse weld at the end of the channel only. Use A36 Grade 36 steel
with F = 58 ksi. (Ans. C6 × 10.5 LRFD and ASD)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

20. determine the capacity of the details shown below.A992: Fy=50ksi, Fu=65ksiA36: Fy=36ksi, Fu=58ksieffective bolt hole diameter = bolt hole + 1/16"beam properties: tw=0.38 in., bf=7.07 in., tf=0.63 in.Fexx=70ksit) what is the weld capacity perpedicular to the beam of the flange connection in kips? (2 decimal places)
Explain how agency benefits of a transportation project is estimated? Use a toll highway project to outline your proposed method.
Please Use LRFD * ASD!
Considering the following steel connection. The plates in Pink are 9mm steel plates. The middle plate (Yellow) is 18mm thick. The width of the plate is 100mm. The maximum allowable tension stresses on any of the plates is 100Mpa in Gross Area Yielding and 150 Mpa for Net Area or Tension Rupture. The bolts used are 8mm in diameter, the holes are 10mm in diameter, no need to add 1.6mm. The bolts allow a maximum of 280 Mpa of shear. Determine the maximum allowable "P" of the connection in kN.
Load and resistance Factor design-tension members Q- Look into the block shear failure mode on the angle L4X4X linked to the 1-inch gusset plate with three 1-inch diameter bolts. Steel A36 is the substance.
Five M20 8.8/ bolts are used in the connection between a beam and a column. Both sides of the cleat plate are welded to column using fillet weld (Manual metal arc AS4855 B-E43XX) with size of 5 mm. The design force transferred from beam to column is 300 kN. The cleat plate has thickness of 12 mm, fy = 300 MPa, and fü = 360 MPa. Determine the unit stress sustained by the weld
A PL 38 X 6 tension member is welded to a gusset plate as shown. The steel is A36 (Fy = 36ksi, Fu = 58ksi). a. The design strength, Pu based on gross area b. The design strength, Pu based on effective area PL % x 6 3/8" 6" Cross Sectional area of PL3/8x6 a) Blank 1 b) Blank 2 Blank 1 Add your answer Blank 2 Add your answer
A PL3/8"X6" tension member is welded to a gusset plate as shown in the figure. The steel specification is ASTM A36. Assume that and compute the following: a) The design strength per LRFD b) The design strength per ASD PL ¾ x 6