Q.1 In a steam power plant located in Baghdad, the steam passes adiabatically and steadily through a steam turbine at a mass flow rate of 12 kg/s. The entrance of the turbine has the following properties ( Velocity3D 80 m/s, pressure=40 bar, Temperature=500°C). The outlet conditions are ( Velocity= 50 m/s, pressure= 0.3 bar, dryness fraction = 92%). Start your solution from the energy balance equation then calculate: (a) the amount of change in kinetic energy, (b) the steam turbine power output, and (c) the area of the inlet turbine.

Q.1 In a steam power plant located in Baghdad, the steam passes adiabatically and steadily through a steam turbine at a mass flow rate of 12 kg/s. The entrance of the turbine has the following properties ( Velocity3D 80 m/s, pressure=40 bar, Temperature=500°C). The outlet conditions are ( Velocity= 50 m/s, pressure= 0.3 bar, dryness fraction = 92%). Start your solution from the energy balance equation then calculate: (a) the amount of change in kinetic energy, (b) the steam turbine power output, and (c) the area of the inlet turbine.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Solve question no.2 and show a clear and organized solution. Answer a, b, c, and d. Also, write the GIVEN and REQUIRED. Thanks!!!
Carbon dioxide gas is compressed at steady state from a pressure of 16 Ib;/in? and a temperature of 32°F to a pressure of 50 lb;/in? and a temperature of 120°F. The gas enters the compressor with a velocity of 30 ft/s and exits with a velocity of 80 ft/s. The mass flow rate is 3000 Ib/hr. The magnitude of the heat transfer rate from the compressor to its surroundings is 5% of the compressor power input. Use the ideal gas model with c, = 0.21 Btu/lb-°R and neglect potential energy effects. Determine the flow area at the inlet, in ft?, and the power required by the compressor to work, in horsepower.
STEAM PROCESSES
IMPORTANT NOTE: THE VALUE OF K IS 865 (K=865). PLEASE ANSWER ASAP THANK YOU!!
Termodynamic question I NEED ANSWER RARIDLY PLEASE!!! Water vapor enters the steam turbine at 4000 kPa pressure, 500 ° C temperature and 6 m3 / h volume flow, shown in the figure below. 0.2 times the mass flow rate of the incoming water comes out of the outlet no. 2 with 500 kPa pressure and 200 ° C temperature. 0.8 times the mass flow rate of the water comes out of the outlet no.3 with 30 kPa pressure and 0.85 dryness degree. Since the heat transfer from the turbine to the environment is 5000 kW, Find the mass flow rate of the incoming water. Find the volume flow of water at outlet no. 3. Find the power (kW) produced by the turbine. (Changes in kinetic and potential energies are negligible)
Rankine Cycle What two conditions can you define for state 2 (pump) that are inferred from other states?
Air is expanded in a multi-stage axial flow turbine, and the pressure drop across each stage is very small. Assuming that air behaves as a perfect gas with ratio of specific heats γ, derive pressure-temperature relationships for the following processes: A) Reversible adiabatic expansion: B) Irreversible adiabatic expansion, with small stage efficiency ᵑp ; C) Reversible expansion in which the heat loss in each stage is a constant fraction k of the enthalpy drop in that stage.
T5.1
A water feed pump operates with a mass flow rate of 464 kg/s. The inlet pressure is 689 kPa and the outlet pressure is 26 MPa. Water enters the pump at 422 K. Assuming an isentropic efficiency of 85%, estimate the power required to drive the pump.
Thermodynamics
A reciprocating air compressor takes in air at 1 bar, 25 deg. C, and compresses it to a pressure of 5 bar running at 300 rpm. The compression follows the PV1.3=C. The clearance is 4% of stroke volume and mass flow rate of air 0.1 kg/s. Determine the power input to the compressor, and volumetric efficiency. Represent the process on p-v and T-s planes. Assume for air R=287 J/kg.K
6- The inlet conditions to a steam nozzle are 10 bar and 250°C. The exit pressure is 2 bar. Assuming isentropic expansion and negligible velocity, determine for 0.2 kg/s of steam: (i) The throat area. (ii) The exit velocity. (iii) The exit area of the nozzle. JAns. (i) 1.44 cm2; (ii) 795 mls; (iii) 2.15 cm2]