Q: Estimate the size of fillet weld for the bracket shown in the figure subjected to a complete reversible load = 5000 lbs with the factor of safety -2 and 600000 cycles? 10 in 4 in F F=5000 lbf 0.5 in

Q: Estimate the size of fillet weld for the bracket shown in the figure subjected to a complete reversible load = 5000 lbs with the factor of safety -2 and 600000 cycles? 10 in 4 in F F=5000 lbf 0.5 in

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

QUZ/ Create an estimated (S-N) diagram and define its equation for an axial fully reversed loaded steel bar. Its cross section shown in figure (1). Determine the life in cycle that can be expected if the alternating stress is 121.231 Mpa. The bar surface finch is hot rolled. The operating temperature is 503 Co and out = 598.954 Mpa. h= 148.929 mm b= 148.929 mm Fig. 1
A beam is supported and loaded as shown in the figure. Data: L = 1000 mm, c = 300 mm, f = 100 mm, D = 100 mm, d = 80 mm. The beam consists of different parts that are welded, and the fillet weld size a is 4 mm. The load q is 2 kN/m, and P = 10 kN. Calculate the maximum stress in the welds.
The bracket shown in the figure is bolted a ceiling beam to support a fluctuating vertical load imposed on it. The bolts are -in coarse-thread SAE grade 8, tightened to recommended preload for nonpermanent assembly. The stiffnesses have already been computed and are kp=4 Mlb/in and km = 16 Mlb/in. Laad line F. Steady stress (a) Assuming that the bolts, rather than the welds, govern the strength of this design, determine the safe repeated load that can be imposed on this assembly using the Goodman criterion with the load line in the Figure and a fatigue design factor of 2. (b) Compute the static load factors based on the load found in part (a). (ie. Yielding factor of safety, Load factor of safety and factor against joint separation)
A tensile load of 330,000 N is applied to a copper pipe with maximum allowable stress of 110 MPa and 80 mm inner diameter. What should be the thickness of the pipe? Choices: A. 9.78 mm B. 12.35 mm C. 11.56 mm D. 10.55 mm
01: A hollow steel tube (1) with an outside diameter of 2.75 in. and a wall thickness of 0.25 in, is fastened to a solid aluminum rod (2) that has a 2 in. diameter and a solid aluminum rod (3) that has a 1.375 in. diameter (E -30,000 ksi, E-10,000 ksil. The bar is loaded as shown in figure below, Determine: (1) the displacement of point D with respect to the fixed support at A. (2) the maximum normal stress in the entire axial assembly. (3) the normal strain in the steel tube (1). 34 kips 18 kips 25 kips 18 kips 34 kips 60 in. 40 in. 30 in.
P
need please asap
MPa) which requires at least a pressure of 10 MPa to prevent leakage. Problem 8.5 A joint in the figure uses a compressed asbestos gasket (E-480 Dimensions are in mm 10 20 200 100 D 150 The cover plate is tightened by using 8, metric grade 5.8, M10x1.5 bolts. If the cylinder is to be rated for an internal pressure of 3500 kPa, calculate the necessary tightening force per bolt for a factor of safety of 2.
A bracket shown in Fig.(2) is fastened to the wall by four bolts equispaced on a (10 cm) diameter bolt circle. The bracket is subjected to a fluctuating force (0-50 N) . Find the forces acting on each bolt and then choose a suitable bolt size and a preload that will give minimum safety factor (1.5) for any mode of failure.