Q) A simply supported beam shown is loaded as shown in figurel-1. It has the cross section as shown in the figure 1-2. If Isa = 10.57 x 10' mm Find the: 1. The maximum flexural tensile stress in the beam and its location. 2. The flexural tensile stress at a section Im from the left and 20 mm from the top edge of the section. 3. The minimum flexural compression stress in the beam. 4. The maximum flexural compression stress at a section in the middle of the beam. 5. The flexural tensile and compressive stress at the right reaction (i.e. right support). 20 mm 20 kN/m 100 mm 40 mm 3m 2m 200 mm Figure 1-1 Figure 1-2

Q) A simply supported beam shown is loaded as shown in figurel-1. It has the cross section as shown in the figure 1-2. If Isa = 10.57 x 10' mm Find the: 1. The maximum flexural tensile stress in the beam and its location. 2. The flexural tensile stress at a section Im from the left and 20 mm from the top edge of the section. 3. The minimum flexural compression stress in the beam. 4. The maximum flexural compression stress at a section in the middle of the beam. 5. The flexural tensile and compressive stress at the right reaction (i.e. right support). 20 mm 20 kN/m 100 mm 40 mm 3m 2m 200 mm Figure 1-1 Figure 1-2

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The beam is subjected to a point load and a distribution load as shown in Figure 3-1 below. (a) Find the reaction from supports B and E.(b) Draw a beam's Shear Force Diagram.(c) Draw the moment diagram of the beam.(d) If the cross-sectional area is shown in Figure 3-2, how many mm is the neural axis NA from the bottom? (e) Find the second moment of area, INA from the neural axis.(f) Find the maximum shear stress mmax from the beam.(g) Find the maximum tensile flexural stress mmax, T and maximum compressive flexural stress mmax, C on the beam, respectively.
A built-in cantilever beam with a hollow rectangular cross-section is subjected to a uniformly distributed load as shown in Figure Q1 below. Which of the following statements best describes the shear force variation along the length, in the x direction, using the sign conventions provided in lectures? Figure Q1 O a ltis constant and positive throughout the length. Ob.it is constant and negative throughout the length. Ocit begins as a negative value and increases linearly to reach a positive value of the same magnitude. Od. None of the provided answers are correct. Oelt begins with a positive constant value for half the length, then suddenly decreases to a negative value, remaining constant for the remaining length. Of. It increases linearly from zero, then continues at a constant value before decreasing linearly to reach a value of zero again. Og It begins as a positive value and decreases linearly to reach a value of zero at the end of the length of the beam.
Gerilme-Şekil Değiştirme Diyagramı = Stress-Strain Diagram
Rectangular cross-section and width given the loading state in the figure Bending safety stress of the beam with b = 150 mm em=10 MPa, Since shear safety stress em = 600 kPa, In order that the stresses that will occur do not exceed the safety stress values What should be the minimum height h of the beam section. 6 kN/m h -3 m -2 m
Homework : In the Figure below , a cantilever beam is subjected to an inclined force ( P ) ; calculate the 1- Normal stress . 2- Shear stress .
For the simply supported bar in the Figure, draw the Bending Moment (M) and Shear Force (V) diagrams, determining the necessary equations and the appropriate numerical values.
The built-up beam is subjected to a moment of M = 80 kNm. Variable d₁ d₂ d3 da Values for the figure are given in the following table. Note the figure may not be to scale. d5 d3 de d₁ Value 128 mm 22 mm 276 mm 11 mm 138 mm d4 12 mm M₁ de d5 a. Determine the distance from the Neutral Axis to the top of the beam, N.A. b. Determine the mass moment of inertia of the beam, I. Determine the max compressive stress acting on the beam, compression c. d. Determine the max tensile stress acting on the beam, tension.
Question Four A beam of the cross section that is shown in Figure a was supported by two rigid supports that tilt by 45° from the horizontal ( see Figure b). The own weight (w) of the beam is 1.5 kN/m. allowable tensile stress (o), = 50 MPa. Calculate the maximum length (L) of the beam that can be supported. 20 cm ... 45 If the maximum %3D 40 cm 15 cm 10 cm (а) 450 (b)
Q1: A simply supported beam as shown in figure (1-A) below, having an I-cross section, has an over all width 200 mm and all depth 300 mm with flanges and web of thickness 20 mm shown in figure (1-B). (a) Draw the shear force and bending moment diagrams of the beam; (b) Determine the maximum compression and tension bending stress which can setup in the beam. - 25 20 kN 20 kN 10 kN 150 60 kN/m (All dimensions in mm) 30 kN/m 100 1.5 m Im Im Im 50 5050, 50 50. Figure (1-A) Figure (1-B)
b) The beam shown in Figure Q3 (b) and (c) is made of steel with Young's Modulus of 200GPA and Yield Stress of 250MPA. The length L is 4m and the beam is pinned at A and supported by a roller at B. Calculate the Elastic-Plastic Moment for the cross-section shown in Figure Q3 (c) if the depth of plastic zone is 4mm. i. ii. Determine the value of distributed load w shown in Figure Q3 (b) if the length of the yielded zone is 50mm. t b A B h L Figure Q3 (c) Figure Q3 (b) Front view of simply supported beam Cross-section of beam b = 100mm, h = 40mm t = 4mm
4. Two tubular sections shown in Figure-2, have the same wall thickness and same circumference. Neglecting the stress concentration, find the ratio of shear stresses for equal twisting moments for two cases. t a t > 2 1 Figure-2
es A gear reduction unit uses the countershaft shown in the figure. Gear A receives power from another gear with the transmitted force FA applied at the 20° pressure angle as shown. The power is transmitted through the shaft and delivered through gear B through a transmitted force Fg at the pressure angle shown. For the steel countershaft specified in the table, find the deflection and slope of the shaft at point A. Use superposition with the deflection equations in Table A-9. Assume the bearings constitute simple supports. In the figure below, FA is 310 lbf and the diameter of the shaft (dshaft) is 1.29 in. dshaft Gear A 20-in dia. 16 in FA 20⁰ The deflection at point A is The slope at point A is 14 in 100 Gear B 8-in dia. rad. 9 in in. B FB 20°