Q-4 1: A compound cylinder formed by shrinking one tube to another is subjected to an internal pressure of 90 MPa. The internal and external diameters of the compound cylinders are 180 mm and 300 mm respectively, and the common diameter at the junction is 240 mm. After shrinking, the shrinkage pressure at the common surface is 12 MNm Draw the hoop stress distribution in the compound cylinder, showing the major values.

Q-4 1: A compound cylinder formed by shrinking one tube to another is subjected to an internal pressure of 90 MPa. The internal and external diameters of the compound cylinders are 180 mm and 300 mm respectively, and the common diameter at the junction is 240 mm. After shrinking, the shrinkage pressure at the common surface is 12 MNm Draw the hoop stress distribution in the compound cylinder, showing the major values.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Refer to the figure. The steel rod is supported by an aluminum plate of 8 mm thickness. Force P pulls down the rod through the 12 mm hole in the aluminum plate. Neglect all weights of the rod and plate, and based on the design criteria that the maximum allowable shear stress in steel to be 18 MPa, calculate the allowable value of P in kN. Round to the nearest tenth. 10 mm T 12 mm- 40 mm- P 8 mm
Q-1 Compute the max load (P ) if the stress in steel 120 Mpa and in bronze 70 Мра steel bronze A= 300mm2 E=83 Gpa 900mm2 E=200 Gpa L=4m L=3m 3m 3m 1m In the fig three rivets of 25 mm diameter joins the plates that are each 130 mm wide .The shearsress in the rivet is 80 Mpa and the stresses in the bearing are 120 Mpa . Determine .a)The minimum thickness of each plate .b) the largest average tensile stress in the plate 25mm Ø 130 Q-3 Two solid shafts of different material are rigidly fastened together and attached to rigid supports as shown in fig .Compute the maximum shearing stress developed in the assembly 3 m 2 m aluminium G=83 Gpa steel G=28 Gpa 50 mm dia 25 mm dia T= 2 kN .m
Question: Consider that the fit between the elements shown in the Figure below is H6/s5. They are both made of SAE 1340 OQT 1000 steel (Sy= 950 MPa, E = 200 GPa). Take D; = 75 mm and D, %3D %3D 90 mm. Determine the maximum possible value of the tangential stress at the inner surface of the outer element in MPa. NOTE: Answer is not 4750MPA. If you Submit This answer I will Directly report. |D, H6/s5 D. 6/7
20 FF 170 A 30 Ölçüler mm cinsindendir. A-A kesiti When the torture in the figure squeezes the material, the maximum force F in the clamping jaws is 1 kN. Calculate the maximum normal stress in section A-A according to the given?
Find the size of 14 bolts required for a CI engine cylinder head. The diameter of the cylinder is 400mm and the steam pressure is 0.12N/mne.Take the permissible tensile stress as 35MPa.
asap pls
For the hollow built-in pipe with an inner diameter of 48 mm and an outer diameter of 60 mm, the forces given in the figure were applied. Calculate the stresses at point A by reducing the applied forces to point B, then to the cross section at A and show them on the stress element.
(a) Figure 1.1 shows a thick cylinder with inside radius of r;=94 mm and outside radius ro =136 mm was pressurized internally Pi = 56 MPa and externally Po= 26 MPa. Analyse: i. The hoop stress and radial stress on internal and external surface of the cylinder. ii. The hoop stress and radial stress at r= 115 mm. iii. The maximum and minimum shearing stress. iv. Sketch the distribution of hoop stress and radial stress along the cylinder wall. Po Figure 1.1 The thick cylinder
use abaqus to solve this
A steam boiler is to have a 300 mm diameter hand placed hole on one end. If themaximum internal pressure is 1.3 MPa, how many 15 mm holes will be required to keepthe cover plate in position? The root diameter of a 15 mm bolt is 12 mm. The allowabletensile stress in the bolts is 100 MPa and the initial stress in the bolts when they aretightened is 600 MPa.
Answer is Not 43,-1 and 22.
10.5 (B) A compound tube of 300 mm external and 100 mm internal diameter is formed by shrinking one cylinder on to another, the common diameter being 200 mm. If the maximum hoop tensile stress induced in the outer cylinder is 90 MN/m² find the hoop stresses at the inner and outer diameters of both cylinders and show by means of a sketch how these stresses vary with the radius. [90, 55.35,-924, 57.8 MN/m²]