Q-3-) V-346.41 V b Z=0+339 Z=0+1350 Z=0+/3Ω Line V₂ R R=1252 Star-Connected load R b-) Find the voltage drop value in the energy distribution line. c-) Find the voltage V₂ at the load ends at the end of the line. R B R R=1892 C Delta-Connected load In the figure above, two balanced 3-phase delta and star-connected loads are connected in parallel to a balanced three-phase power distribution line. Delta and star connected loads are completely resistive and the resistance values per phase are 18 2 and 12 2, respectively. The phase-to-phase voltage value of the source feeding the line is 346.41 V (rms), and it is assumed that the three-phase network between the source and the load has an inductive reactance value of 3j per phase. a-) Find the total current drawn from the source, active and reactive power values by selecting the Van voltage as a reference value.

Q-3-) V-346.41 V b Z=0+339 Z=0+1350 Z=0+/3Ω Line V₂ R R=1252 Star-Connected load R b-) Find the voltage drop value in the energy distribution line. c-) Find the voltage V₂ at the load ends at the end of the line. R B R R=1892 C Delta-Connected load In the figure above, two balanced 3-phase delta and star-connected loads are connected in parallel to a balanced three-phase power distribution line. Delta and star connected loads are completely resistive and the resistance values per phase are 18 2 and 12 2, respectively. The phase-to-phase voltage value of the source feeding the line is 346.41 V (rms), and it is assumed that the three-phase network between the source and the load has an inductive reactance value of 3j per phase. a-) Find the total current drawn from the source, active and reactive power values by selecting the Van voltage as a reference value.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Analyze AC network using Kirchhoff's Laws. Find the branch currents indicated in the following networks. PS: Show complete/step-by-step solution without rounding off any numbers.
28 k
A conventional phase transformer given in the figure will be connected as an autotransformer in two different ways. Each For a connection, find the input and output powers by drawing the connection. a) Connection of 1220 / 220V autotransformer b) 1000 / 1220V autotransformer connection
Q- A 30 KVA, 2500/230 transformers has leakage impedance of 8%. Find the voltage to be applied on hV side to circulate full load current with low voltage winding shorted.
A delta connected load (Figure 2) has an impedance Z is(12 + j35) ohms. If the applied VAB voltage is 380 V with -50º phase . Get the current IC and load IAB current.
From the circuit below, determine secondary winding voltage Vsec if the primary winding voltage Vpri = 120Vrms? %3D Np:Ns 6:1 D. Vp 120 Vac 60 Hz Vout R = 200 Q O 20Vrms O 720Vrms O 120Vrms O Ovrms wi m
A three-phase system has balanced conditions so that the per-phase circuit representation can be used as shown in Figure 1 Select the turns ratio of the step-up and step-down transformers that the system operates with an efficiency greater than 99 percent. Moreover, find the complex power (received or given) of all components in the circuit and the V1 and V2 voltages. The load voltage is specified as 4 kV rms, and the load impedance is 4/3 ohm. ..
Question No.33 A single phase half bridge VSI has load R = 1.8 Q and DC source voltage 130 – 0 – 130 V. Find the power delivered to the load due to fundamental current.
SHOW COMPLETE SOLUTION A. What is the overall power factor of the two loads as seen by the source? Use two decimal places. B. Determine the magnitude of the current passing through Load 1. Use amperes and two decimal places. C. Is the overall power factor leading or lagging?
Q- A 30 KVA, 2500/230 transformers has leakage impedance of 8%. Find the voltage to be applied on hV side to circulate full load current with low voltage winding shorted.
1- Your example deduced the total strength of the following three loads: the first load 1200VA at a power factor of 0.7 late, the second load 350VA at a power factor of 0.5 was late, and the third load 3275VA at a power factor of 1.0.
A balanced load is connected in star across a 3 phasec415V 50Hz supply. The load consists of a coil of resistance 25 ohms and inducrance 0.5 henry in paeallel with a purw resistance of 28 ohms and a pure capaciror of 60microfarads capacitance ,in each branch. Calculate a. The line currents? Need full working and answer has to be 9.3A Formola for inductance XL= 2×3.142FL FORMOLA FOR CAPACITOR XC= 1/2×3.142×FC