Three single-phase transformers (ideal) are connected as shown inthe figure below to supply a balanced 3-phase, 150 KVA, 600 VLload from primary 4.16 KVLLline.H1X1H2X2BALLANCEDH1X1THREE PHAGELOADH2X2H1X1X2(a)Draw (neatly) a phasor diagram showing the three, primaryline-to-line voltages and the six secondary phase and linevoltages. What is the phase relationship between the primaryvoltage VAB and the secondary voltage V12? Indicate on thephasor diagram:f

Please find your answer below in step 2

the figure below to supply a balanced 3-phase, 150 KVA, 600 VLL load from primary 4.16 KVLL line. BALLANCED THREEPHAGE H1 X1 LOAD HI X1 (а) Draw (neatly) a phasor diagram showing the three, primary line-to-line voltages and the six secondary phase and line voltages. What is the phase relationship between the primary voltage VAB and the secondary voltage V12? Indicate on the phasor diagram: 空

the figure below to supply a balanced 3-phase, 150 KVA, 600 VLL load from primary 4.16 KVLL line. BALLANCED THREEPHAGE H1 X1 LOAD HI X1 (а) Draw (neatly) a phasor diagram showing the three, primary line-to-line voltages and the six secondary phase and line voltages. What is the phase relationship between the primary voltage VAB and the secondary voltage V12? Indicate on the phasor diagram: 空

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Match the following for each sentences
If the line-to-line primary voltage and line current is 1.0 at 0 degrees, what is the secondary line- to-line voltage for the following three-phase transformers? Assume a turns ratio of N = 10. Express answer in polar form. a. Delta-to-Delta: b. Delta-to-Wye: c. Wye-to-Delta: d. Wye-to-Wye:
Question 3. A three-phase impedance load balanced D a connected load in parallel with a balanced ? connected load made of bonding. D each arm for the load ?D = 6 + 6? and ? each arm for the connected load It is given as ?? = 2 + 2?. ? the connected load ?? = 1? is earthed through the neutral impedance. To this impedance load, the symmetrical component voltages ?0 = 10∠60°, ?1 = 100∠0° and ?2 = Unbalanced phase-to-earth voltages ??, ?? and ?? of 15∠200° volts were applied. a) Draw the zero, positive and negative sequence circuits. b) Find the complex powers imparted to each component circuit.
Two single-phase transformers, having equal turns ratio, in parallel supply a secondary load of 1,000 A at 0.8 pf lagging. For each transformer the secondary emf on open circuit is 3,300 V and their total leakage impedances referred to secondary are (0.10 + j0.20) ohms and (0.05 + j0.040) ohm, respectively. Determine the output current on each transformer.
How does a three-phase power system differ from a single-phase power system, and what are their respective applications?
What would be the total single phase 120kVA capacity that could be used with the transformers size of 1.5 kVA?
Positive sequence components consist of 3 equal sized phasors. The phase difference between these phasors is 180 °. And the phasors are in the phase order of the true phasors. Is this statement true or false?
Overhead lines.
In 3-phase balanced delta connected system, the voltage induced in each coil is called
3. A circuit consists of two impedances. Z1 =20230° and Z2 =25260° 2, in parallel, supplied by a source voltage V=1002600 volts. Determine the power triangle for each of the impedances and for the source.
Khalid Abdulrahman Abdullah Alqasmi KA 05 Symm... 9 Search 8 Share O Comments Transitions Animations Slide Show Review View Help 1. A 3- phase, 30 MVA, 33 KV alternator has internal reactance of 4% and negligible resistance. Find the external reactance per phase to be connected in series with the alternator so that steady current on short circuit does not exceed 10 times the full load. Also find Find the full load current. d notes
What is the max load demand of the following feeders 4152 MW, 2.891 MW, 815.20 KW, 905.12 KWand 1.972 MW A) 10,735.32 KW B) 12,815.32 KW C) 10,571 MW D) 12.052 MW