An AC circuit with R, Land C in parallel, has the following branch currents. Resistive branch - 12 A Inductive branch - 11 A Capacitive branch - 6 A The phase angle between the supply voltage and the supply current will be approximately:

An AC circuit with R, Land C in parallel, has the following branch currents. Resistive branch - 12 A Inductive branch - 11 A Capacitive branch - 6 A The phase angle between the supply voltage and the supply current will be approximately:

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.8MCQ: An ac resistance is higher than a dc resistance. True False

See similar textbooks

Related questions

Q: could you help me please it's one question

A: NOTE :- According to our company policy, experts can answer only 3 subparts at a time. So please…

Q: Current Attempt in Progress The figure shows a resistor of resistance R = 6.32 02 connected to an…

Q: In the circuit shown in figure, & = 10.0 V, R₁ = 5.00 S2, R₂ = 10.0 2, and L = 5.00 H. a) Switch S…

A: For the given R-L circuit, the circuit parameters are as follows:ϵ=10 V, R1=5 Ω, R2=10 Ω, L=5 H.

Q: A Cockcroft-Walton type voltage multiplier has ten stages with capacitances, all equal to 0.1 μF.…

A: Given data C=0.1×10-6 FVmax=100 KVf=60 HzI= 5 mAn=10 (a) % ripple Formula for % ripple is given…

Q: List 3 different concepts of Electricity(gravity) not hydro generation using weights design. Each…

A: Concept 1: Piezoelectricity Generation Introduction: Piezoelectricity is a concept that…

Q: A solenoid has a 5.9 cm length, a 13 mm radius, and a total of 1400 windings. Suppose this solenoid…

A: When a solenoid is subjected to alternating current then it generates and magnetic field and stores…

Q: 1/ Suppose that there are two types of H.V.T.Ls operating at the same voltage and carrying the same…

A: In this question we need to choose a correct option.

Q: Vbatt=25 V C1=90 ?C C2=75 ?C C3=60 ?C R1=160 Ω R2=120 Ω t2=21.6 msec t3=27 msec Consider the…

A: Concept: For a RC series circuit with a dc voltage source, The current flowing i(t) is given by:…

Q: What are the primary dimensions of electric voltage (E)? (Hint: Make use of the fact that electric…

A: The electric power is the product of electric current and electric voltage. The electric power is…

Q: For the current curve shown in the figure, given that q(0)= 0.5mC. The charge q(t) at t=5ms is: i(1)…

A: Expression for charge Q(t)=Q(0)+∫I(t) dt. From above we will get expression for Q(t). substitute…

Q: Q2 () () What is the difference between a Wheatstone bridge and a Kelvin bridge? Your explanation…

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: The electrical circuit representing a small axon section of length delta x is shown. Which of the…

A: In the analysis of the electrical properties of the axon, we will use some of the techniques of…

Q: The number of potential interfaces (points of contact) between various parts of a system. Give…

A: The number of potential interfaces, or points of contact, between various parts of a system…

Q: The advantages of splitting vertically and horizontally varies. Describe them.

A: We need to tell about advantages of splitting vertically and horizontally varies.

Q: A mass is connected by a spring and damper to the wall as shown in the following figure. The floor…

A: Given Figure: Given: M = 20 kgK1 = 2N/mK2 = 7 N/mfv1 = 3 N-det/mfv2 = 5 N-det/m Find: calculate…

Q: VDD M1 M2 IIN IOUT

Concept explainers

Wheatstone Bridge Method

A Wheatstone bridge is a circuit used to measure unknown resistance by measuring the ratios of the two branches of the circuit such that each branch has two resistance and out of four resistance one is unknown. The two branches are joined in between with the help of galvanometer which is used to determine the direction of the current. The main advantage of this circuit is that it can provide the most accurate measurement (different from a simple voltage separator).

Question

Show solutions.

An AC circuit with R, Land C in parallel, has
the following branch currents.
Resistive branch - 12 A
Inductive branch - 11 A
Capacitive branch - 6 A
The phase angle between the supply voltage
and the supply current will be
approximately:

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Introduction

VIEW

Solution

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Task 3 A three phase, four wire star connected load consisting of: ZR: a resistor of 9500 in series with a 3H inductor ZB: a resistor of 1950 ZY: a resistor of 1950 in series with a 4µF capacitor Using the equipment available in the power lab (Room T017), connect the given load to a three-phase supply available in the lab and: 3.1. Determine the current of each line and the neutral current and measure the total power supplied by the source. 3.2. Analytically, calculate all currents and the total power and compare with those obtained in measurements. 3.3. Device a method and measure the waveform of the neutral current. Discuss the obtained waveform and the reason for any distortion in the waveform 3.4. Validate your calculations using computer simulation
A 50 Hz high voltage Schering bridge is shown in the figure. The component parameters are as follows under balanced condition: Cs-150 microfarad, C2-0.677 microfarad, R2-634 ohm, and R1-168 ohm. Find the dissipation factor of the tested material. 220V rms Lütfen birini seçin 0.1340 b.0.1672 E0051 0.0.0749 e.0.1128 88888888 00000000 25 kV rms R R₁ R₂ II (C₂ 12²
Please show you detailed solution Number 10 A voltage of 250 volts at 50 Hz is impressed on a circuit having a 60-ohm resistor, 35-?F capacitor, and a 0.25-henry inductor in series. Determine power factor. A. 0.979 C. 0.924 B. 0.862 D. 0.707
Write down the differential equations describing the loop currents of the given circuit. Assume clockwise rotation and i passes through the voltage source. R1 2 Ohms L1 C1 0.5F 0.3H Vs V R3 6 Ohms R2 10 Ohms C2 0.25F
Q4
Show the solution Using 24v AC source design a 24v unregulated power supply circuit that will power a 1kohms load with 50mv ripple. Draw your designed unregulated power supply circuit
A 25-ohm resistor connected in series with a coil of 50-ohm resistance and 150-mH inductance. What is the power factor of the circuit? The standard frequency is 60 Hz. Show complete solution.
As shown in the figure, two metal plates are connected to a voltage Source the seperation astence between the plater is much smaller then Hhe s0 of Hhe plates ond He space between the plates Is tfill ed with a Uniform charge denity p -) Aind the potntial VIx) in between the plater. ) Fnd the ele ctric freld Ex Cx) in between the plater -) find the surface chorge denritres on the mne surpa ed af ept crd indt metal elaes
WWW An Ac circuit with a Power Source has a resistor and an inductor connected in paralle!. The values are as follows: V=194 R = 104 XL = 81 What is the power factor? *****
An inductive reactance of 6 ohm is connected in series with a parallel combination of a variable resistor R and a capacitive reactance of 15 ohm across 100V , 50 hz supply. a. Solve for the frequency so that the magnitude of the inductive reactance is 2 times the magnitude of capacitive reactance. b. Solve for the value of R so that the total current I will be maximum.
D Page view A Read aloud 4Draw NGR 111: Engineering Problems omework #7 202 For the DC circuit shown in Figure P28, find the voltage across each resistor and the current in each resistor. Find the power dissipations in the 20-1 and 100-2 resistors. Use Kirchhoff's Laws 20 2 500n 40 V 752 100 0
For the series RL circuit shown in the figure below, answer the following questions and justify your answer.If the current is kept constant, does the coil have inductance?If the current is kept constant, does the coil affect the current value?Can the reverse emf ever be greater than the battery emf?