Q-2 For the simply supported steel beam [E = 200 GPa; I = 129 × 106 mm4 ] shown in Figure below, assuming a length L = 6 m, concentrated load of 40 kN, and a distributed load w = 30 kN/m, (a) Use the double-integration method to determine the deflection at B.  (b) Use the method of Castigliano to determine the deflection at B.

Q: Use singularity functions to determine the deflection at mid-span for the solid steel shaft shown in…

A: Step 1:Step 2:

Q: The factors of safety predicted at point H by the maximum shear stress theory of failure (Tresca…

A: For the solution refer below images.

Q: A steel beam, of lengths a=4 m and b=4 m and a hollow box cross section, is supported by a hinge…

A: Given data:A steel beam with a hollow box cross-section is given.The beam is supported by a hinge…

Q: A simply supported steel beam of length L = 16 ft is loaded with two forces PA = 350 lbf and PB =…

A:

Q: Use singularity functions to determine the deflection at mid-span for the solid steel shaft shown in…

A: Step 1:Step 2:

Q: A steel beam, of lengths a= 4 m and b=4 m and a hollow box cross section, is supported by a hinge…

A: Given:

Q: A simply supported beam hinged at A and supported at C, is carrying a distributed load and a point…

A:

Q: 1. A semi-infinite steel beam of second moment of area I, = 4.0 × 10° mmª is supported on an elastic…

A: Write the given information.

Q: In the figure, aluminum [E = 60 GPa] links (1) and (2) support rigid beam ABC. Link (1) has a…

A: Data given -  a = 1380 mm, b = 760 mm, L₁= 2570 mm, and L₂ = 4650 mm. P = 32 kN  A2 = 430 mm2  A1 =…

Q: Question 3 For the beam loaded and supported as shown in Figure below, determine the deflection of…

A:

Q: A steel beam, of lengths a=5 m and b=2 m and a hollow box cross section, is supported by a hinge…

A:

Q: A wide-flange member (W 10 x 30) is compressed by axial loads that have a resultant P = 30 kips…

A: Given P = 30 k Modulus of elasticity = 29000 ksi Maximum deflection = 1/500 To find Lmax

Q: Buckling of suwnio Ex. 3: A horizontal beam AB is pin-supported at end A and carries a load Q at end…

A:

Q: answer this; The factors of safety at point H predicted by the maximum-distortion-energy theory…

A: For the solution refer below images.

Q: A propped cantilever steel beam is constructedfrom a W12 x 35 section. The beam isloaded by its…

A: Given data as per question Length of the beam =11.5 ft  E = 30,000 ksi. For   W12 x 35 section  q =…

Q: A steel beam, of lengths a=4 m and b=4 m and a hollow box cross section, is supported by a hinge…

A: A steel beam, of lengths a = 4 m and b = 4 m and a hollow box cross section, is supported by a hinge…

Q: (a) Find peak intensity q,if the deflection at joint Bis known to be 0.18 in. Assume that modulus E=…

A: This is a case of cantilever beam on which load is uniformly distributed. maximum deflection=…

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.