Q 2: - A one cylinders Freon (134a) compressor has a Bore and Stroke 5.4and 4.8 cm respectively. It is speed 1450 rpm volumetric efficiency c.v100% working fluid reaches expansion valve at 42°C and the temperature%3Dof its suction -8°C:-a- Find the mass flow rate of the refrigerant, heat capacity and COPact&COPtho?b- Find the mass flow rate of the refrigerant, heat capacity and COP& COPtho if the clearance factor will be 5%?

Answered: Image /qna-images/answer/6fde9ee5-f6ff-4bc1-8560-8ddb83633b2b.jpg

Q 2: - A one cylinders Freon (134a) compressor has a Bore and Stroke 5.4 and 4.8 cm respectively. It is speed 1450 rpm volumetric efficiency cu = 100% working fluid reaches expansion valve at 42°C and the temperature of its suction -8°C:- a- Find the mass flow rate of the refrigerant, heat capacity and COPact & COPtho? b- Find the mass flow rate of the refrigerant, heat capacity and COP & COPtho if the clearance factor will be 5%? act

Q 2: - A one cylinders Freon (134a) compressor has a Bore and Stroke 5.4 and 4.8 cm respectively. It is speed 1450 rpm volumetric efficiency cu = 100% working fluid reaches expansion valve at 42°C and the temperature of its suction -8°C:- a- Find the mass flow rate of the refrigerant, heat capacity and COPact & COPtho? b- Find the mass flow rate of the refrigerant, heat capacity and COP & COPtho if the clearance factor will be 5%? act

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

7. A single stage air compressor handles 0.5 cubic meter per sec of atmospheric air at 27 O C and delivers it to a receiver at 655 Kpa. Its volumetric efficiency is 0.75, its compression efficiency is 0.90 and its mechanical efficiency is 0.9. If it rotates at 400 rpm, calculate the power required to drive if a) compression is isentropic. b) compression is isothermal
9. A 9.5 tonnes capacity of ammonia refrigerator operates between evaporator and condenser temperature of -13°C and 28°C is needed in a food storage locker. The refrigerant is sub-cooled by 4°C before entering the expansion valve. The vapour is 0.90 dry as it leaves the evaporator coil. The compression in the compressor is adiabatic type. Using p-h chart find (i) Condition of vapour at outlet of the compressor (ii) Condition of vapour at entrance to evaporator (iii) С.О.Р. (iv) Power required in kW Neglect valve throttling and clearance effect.
An R22 system has compression raito of 4:9:1 NRE of 72 btu/pd , heat compression of 18 btu/ pd and constant volume of 1.4 cfm at inlet to the compressor . what's the displacement of compressor for 1 ton of refrigerant.
The reheat pressure effect the operating variables and thus turbine performance. Repeat Problem 2 twice, using 0.6 and 1.0 MPa for the reheat pressure For the engine find W and ?? .
Q2/Gas turbine unit having heat exchanger with thermal ratio(0.75),ahigh pressure stage turbine drives the compressor and a low pressurestage turbine generate the power. The overall pressure ratio is (5/1) andthe maximum temperature is (1000 o c).The isentropic efficiencies ofcompressor, H.P.T and L.P.T are (0.7),(0.78) and (0.8) respectively andmechanical efficiency of both shafts is (99 %) . Calculate:a- The pressure between turbine stages when the air intake conditionare (1 bar) and (29 oc) b- Thermal efficiency when the mass flow is (30 kg/sec)Cpg= 1.15 kJ/kg.K ɣg=1.33
Q8: In Kaplan reaction turbine produces (70kW) at (370 r.p.m). The hub and tip diameter are (0.4m and 0.8m) respectively. The flow velocity is (2.8 m/s), find peripheral velocity and discharge.
a. Assume a blower operating at 4000 rpm compressing air from 68°F and 14.7psia to 8.5psig, handling 16000cfm at the design point with an efficiency of 70%. It is desired to find the operating conditions (BHP, H and Q) at 3600 rpm. b. Same as problem (a) except assume that the speed and inlet temperature remains the same, but the inlet pressure at the point considered, drops to 10psia. c. Same as problem (a) except assume that the speed and inlet pressure remains the same, but the inlet temperature rises to 100°F.
Q8: In Kaplan reaction turbine produces (70kW) at (370 r.p.m). The hub and tip diameter are (0.4m and 0.8m) respectively. The flow velocity is (2.8 m/s), find peripheral velocity and discharge.
ROOM (2) 700kPa x=0 CONDENSER (1) 40°C 700kPa EXPANSION VALVE (3) 100kPa EVAPORATOR (4) 100kPa x=1 OUTSIDE Consider a heat pump cycle operating with R134-a fluid at 0.01kg/s mass flow rate. Conditions are given in the figure. a) What are the values of heat supply rate to the room and heat absorption rate from the outside? b) What is COP of this heat pump? c) Assume we immediately put a watermelon of 8kg to the room at 2°C. Assuming a specific heat of 4200J/kg for the watermelon, how long will it take for the watermelon to reach room temperature of 20°C if we assume that heat pump only heats watermelon? O A) 2.7 minutes B) 3.2 minutes C) 4.4 minutes O D) 5.3 minutes E) 6.2 minutes COMP.
1) A singe acting, twin cylinder, ammonia compressor with bore equal to stroke is driven by an engine at 250 rpm. The machine is installed in a chilling plant to generate 700 kW of refrigeration at -18C evaporating temperature. At this temperature, the cooling effect per kg mass is 1160 kJ. The sp volume of vapor entering the compressor is 0.592 m³/kg. Assume 85% volumetric efficiency. Calculate the bore in mm.
A single-stage single acting air compressor takes air in at 1 bar & delivers at 7.5 bar. Work done by the compressor is 38 kJ and the compressor runs at 150 rpm. Calculate the power required in kW/? the power required in kW?
iii) the exit area of the nozzle. Take Cp = 1.005 kJ/kg-K and R=287 J/kg-K Q.B3. A heat engine operates between two reservoirs at 400°C and 30°C. Half the power produced by the heat engine is used to drive a Carnot heat pump that removes heat from the cold surroundings at 2°C and transfers it to a house maintained at 27°C. The heat engine is absorbing heat at a rate of 5 kJ/s. i) Draw the complete schematic of the device ii) Determine the thermal efficiency of the heat engine iii) Determine the coefficient of performance of the heat pump iv) Determine the rate of heat loss from the house. v) Determine the minimum rate of heat extraction by the heat pump, and vi) the total rate of heat rejection.