A process in a plant is to he revised such that the airflow rate through Si system will increase from 8000 cfm to 10,000 cfm, The existing fan runs at 1600 rpm and provides 6,0 in, H2O SP. Estimate the new speed required for this fan and the new SP.

A process in a plant is to he revised such that the airflow rate through Si system will increase from 8000 cfm to 10,000 cfm, The existing fan runs at 1600 rpm and provides 6,0 in, H2O SP. Estimate the new speed required for this fan and the new SP.

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter40: Typical Operating Conditions

Section: Chapter Questions

Problem 10RQ: The seasonal energy efficiency ratio (SEER) includes the energy used in the _____and _____cycles.

See similar textbooks

Similar questions

Three disadvantages of parallel compressor systems are _____, _____, and ____.
A compressor must operate in a speed range between 0 and 1500 rpm. The friction torque of Coulomb Tc is 10 N. m. What should be the required Tw working torque if the compressor constant is 0.5 N. m. s. What is the power required by the engine that operates this compressor?
An air conditioning supply fan is operating at and requiring 4.85kW. 600 RPM against is delivering 540m / min at 500PA SP It standard conditions. In order to handle air conditioning load, heavier than originally planned, more air is desired, in order speed SP and to increase flow are the new power?
Please read the problem and solve what is asked. Thanks! A two-stage compressor with an ideal intercooler receives 0.5m3/s of Helium at 150kpa and 300K and discharges it at 7500kpa. Find the heat rejected(kw) at the intercooler. Ans. 27.015 kw
1. define the cutfof ratio and the compression ratio 2. air is compressed at a constant temperature find the word done on the fluid under the: - initial pressure 200 kpa - final pressure 1500 kpa - compression temperarture 600 k
1) A singe acting, twin cylinder, ammonia compressor with bore equal to stroke is driven by an engine at 250 rpm. The machine is installed in a chilling plant to generate 700 kW of refrigeration at -18C evaporating temperature. At this temperature, the cooling effect per kg mass is 1160 kJ. The sp volume of vapor entering the compressor is 0.592 m³/kg. Assume 85% volumetric efficiency. Calculate the bore in mm.
Exampie Air conditioning unit uses Freon R-22 for conditioned office at 25 C. The evaporating temperature is 17 C and the condensing temperature is 47 C. The compressor is reciprocating and single acting with number of cylinders of 4, volumetric efficiency of 0.9, number of revolution is 900 rpm cylinder dimensions of L/D is 1.25. If the compressor power is 3 kW and mechanical efficiency of 0.9, estimate the followings: the refrigerant mass flow rate in kg/min, refrigeration capacity in TR, cylinder dimensions, condenser heat load, coefficient of performance and relative efficiency. and
(a) What would be the necessary bore and stroke of a single acting four- cylinder, 350 rpm ammonia compressor working on simple saturation cycle between 35°C condenser and -15°C evaporator temperatures and developing 15 tons refrigeration. Given for the compressor: Ratio of stroke to bore = 1 Volumetric efficiency = 0.7 (b) If the index of compression is 1.15, find the error introduced in calculat- ing the work of compression by assuming the process to be isentropic. Also, find the heat rejected to the compressor-jacket cooling water.
The condensing pressure for a Rankine engine is 0.001325 MPavac. Calculate the following for steam flow rate = 1 kg/sec of steam when the steam at the beginning of expansion is at 119.6 deg SH and 4.0 Mpaa. Draw the TS and equipment diagrams for the ideal and actual case and find for the following for the ideal case: Pump work in KW. Ans. Ideal heat rate in KJ/KW-hr. Ans. Rankine engine efficiency (%). Ans. Cycle thermal efficiency ( %). Ans
Air is at temperature of (290 K) flows in a centrifugal compressor running at (20000 rpm). The other data are given as - isentropic efficiency is (0.80), outer diameter of blasé tip is (600 mm), slip factor is (0.80) Calculate: (i) The temperature rise of air passing through the compressor. (ii) The static pressure ratio Assume absolute velocity of air at inlet and outlet of compressor are the same. Take for air Cp = 1.005 kJ/kg-K, y = 1.4.
a. Assume a blower operating at 4000 rpm compressing air from 68 degree Fahrenheit and 14.7psia to 8.5psig, handling 16000 cfm at the design point with an efficiency of 70%. It is desired to find the operating conditions (BHP, H and Q) at 3600 rpm.b. Same as problem (a) except assume that the speed and inlet temperature remains the same, but the inlet pressure at the point considered, drops to 10psia.c. Same as problem (a) except assume that the speed and inlet pressure remains the same, but the inlet temperature rises to 100 degree Fahrenheit.
Q 2: - A one cylinders Freon (134a) compressor has a Bore and Stroke 5.4 and 4.8 cm respectively. It is speed 1450 rpm volumetric efficiency c.v 100% working fluid reaches expansion valve at 42°C and the temperature %3D of its suction -8°C:- a- Find the mass flow rate of the refrigerant, heat capacity and COPact& COPtho? b- Find the mass flow rate of the refrigerant, heat capacity and COP & COPtho if the clearance factor will be 5%?