Q. The following pasticulars refer to a twat Tow velacity-Compounded impulse wheel which fome of a the first stage combination turbine: Steam velacity at nozzle outled: 630m blade velocity Alozzle angle Outlet augie, first yau Dutlel augle, fixed guide bades: 22 Suttlet augle,teond 2o2 of mewving bladsi 36 Steam flow sale : 125 m/3 Mean of 18° mouing blede i The radio of the relatine velocity ot outlet to that 0.84 determine : at inlet s the tahle for all 9) The 62779fauge_fif thst on the blades o The axial thrust on the dlades the porer developed. 0 the lading efficiency. velocity of whid.

Q: Determine the Resultanto f the eoplanar orcesestem

A:

Q: Consider the equation for angular twist due to torsion. Imagine you are designing a solid round…

A: The angular distortion of an item caused by a couple of twisting torques is known as the angle of…

Q: how does F_BC equal 6

A:

Q: (b) Compute the internal torque exerted on gear A (TAC), gear C(TcD) and gear D (TDB). (c) Sketch…

A:

Q: y' = -y tan x, y(0) = 2

A:

Q: 10 kNim 50 kN Identify the moment diagram of the beam shown. 3125 3125 (AN mA 022 (AN-m)A

A:

Q: What is the maximum magnitude of the bending moment caused by force G? If none, enter zero. Do not…

A: It is required to determine the magnitude of the maximum bending moment by the force G.

Q: 3. both wires is identical at 1.5 meters and both wires are 5 mm in diameter. The steel wire is made…

A:

Q: дл др Os ӘТ S Cp

A: Write the expression at constant enthalpy. dh=Tds+vdP0=Tds+vdP∂s∂ph=-vT

Q: (a) Determine the -position of the centroid of the figure shown on the next page. (and draw it on…

A:

Q: can you answer 1B

A:

Q: The equation of the unit circle is _______________.

A:

Q: -150 mm 15 mm B C 150 mm -15 mm 15 mm - 100 mm·

A: given;

Q: You are designing a new engine; this device operates with liquid fuel as an input and gener energy…

A: Hello. Since you have posted multiple questions we will solve the first question for you. If you…

Q: Q.2 A cantilever beam of length / = 5 m, flexural rigidity El in MPa, and mass m = 1950 kg carries…

A:

Q: 28 cm a? 100 cm 30° V 15 cm

A:

Q: (4) 8.8.8.8 16 8 8 16 21

A: the question is not fully asked   bricks and blocks are given

Q: 620 mm 125 350 mm

A: Consider the line diagram of the following figure as shown below – From the line diagram, it is…

Q: Add the length of all the horizontal pieces. They go left and right.

A:

Q: What is the length and wall thickness of the vertical bear

A: For figure 2,  drawing and the type of symbols present

Q: Fload/8 Fload/4 ffort = Fload/8

A: According to the details provided in the question, we need to calculate  we need to find all forces…

Q: how can I get the 85 α

A:

Q: ENTIRE ANSWER IS WRONG

A: Initial velocityFinal velocityInitial angleFinal angleWeight of the basketball

Q: Incorrect please resolve both parta

A: To calculate the surface temperature of the tank when it is passed through water and to calculate…

Q: Crossed center lines are used in the .. . view Longitudinal Horizontal Circular All

A: Solution:

Q: In this case, the applied force is always pulls upward, but the amount of force that can be applied…

A: According to the given data  We need to find The true statement

Q: Findss 30 kN-m

A:

Q: (12m) ladder weighs 200N and is ed against a smooth vertical wall its lower and (6m) from the wall

A:

Q: A piston-cylinder device contains 1.5 kg of steam at 300°C and 0.4 MPa. Steam is cooled at constant…

A:

Q: A) Are all the nodes in the same plane?. B) To the surface, what would the unit of perpendicular…

A: The 3 dimensional geometric coordinates of the system are taken in uniform units as millimetre. They…

Q: Figure 1 of 1 30 40 F2

A: Given, F1 = 210 N F2 = 510 N Angle between two forces = θ = 40°

Q: At a given moment four link mechanism OABO, is in the position shown on the figure and OA= AB = AO =…

A:

Q: (d) Water flows in two different horizontal pipes having a height difference of 55cm. A U- tube…

A:

Q: The brake piston consists of a full cecular part. Its cross section is shown in ( Eigure 1). Suppose…

A: Cross-section:a=18 mmb=80 mmc=55 mmd=35 mme=30 mmf=45 mmTo determine: interior surface area of brake…

Q: The point 1/4 of the way from (1,-3, 1) to (7,9, –9) is A. (4,3,-4) O B. (3/2,3,-3/2) OC.…

A: A point's coordinates are a pair of integers that define its precise position on a two-dimensional…

Q: How do you know that it is -1.2? What determines the sign?

A: Given: How do you know that it is -1.2? What determines the sign?

Buckling of columns

The column is described as a vertical member of the structure that carries an axial compressive load, and buckling is a lateral deformation of the column under the application of load.