Pump BC shown brings oil (SG = 0.72) to reservoir D at 170 L/sec. The energy lost from A to B is 1.1 J/N and from C to D is 4.7 J/N. El. 84 m D EL 22.6 m A 0.30-m Ø B El. 2.8m How many hp does the pump supply the system? O 108.164 hp O 112.069 hp O 150.228 hp O 80.690 hp

Pump BC shown brings oil (SG = 0.72) to reservoir D at 170 L/sec. The energy lost from A to B is 1.1 J/N and from C to D is 4.7 J/N. El. 84 m D EL 22.6 m A 0.30-m Ø B El. 2.8m How many hp does the pump supply the system? O 108.164 hp O 112.069 hp O 150.228 hp O 80.690 hp

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: In the system below, a flow rate of 200 lt / s enters the pump from the Y point and exits from the A…

A: The flow of fluid includes movement of an unbalanced fluid. As long as unequalled forces are in…

Q: I- The pump shown delivers I15 Uifers/sec of oil, q gr. = 0.84 to reservoir D at elevation 72m. The…

Q: Q2)For the system shown in the figure, the water flow rate is (40)L/s. Find the 30m power…

A: To find :- Power transferred from the flow by the turbine.

Q: A 70-mm-diameter suction pipe leading to a pump, as shown below, carries a discharge of 0.05 of oil…

Q: 2-18: A pelton wheel has a mean bucket speed of 10 m/sec with a jet of water flowing at the rate of…

A: Mean bucket speed (u1 = u2 ) = 10 m/s Flow rate (Q) = 0.7 m3/sec Head (H) = 30 m Deflection angle…

Q: 2. A centrifugal pump shall be used as the firepump on a ship. It shall deliver a head of 120 m…

A: step 1-

Q: water pump at elevation 46 m. is used to bring up 250 gpm of water from a river (elev. 45 m.) to…

A: Discharge is 250 gpm Elevation of reservoir is 100 m

Q: Q2)For the system shown in the figure, the water flow rate is (40)L/s. Find the 30m power…

A: Given Discharge, Q = 40 l/s = 0.04 m3/sec Kinematic viscosity = 1 x 10-6 m2/s Total head = 30 m To…

Q: Water is to be moved from one large reservoir to another at a higher elevation as indicated in the…

A: Diameter of the pump, d = 8 in 1 ft = 12 inch Diameter of the pump, d = 0.67 ft Acceleration…

Q: pump is used to raised water to a reservoir through 1000 m. long of 20 cm diameter with Cw of…

A: According to given data- A pump is used to raised water to a reservoir through 1000 m. long of 20 cm…

Q: 3. A pump draws water at 300 liters per second from reservoir A and lifts it to reservoir B as…

A: Given data: Discharge=300 l/s Head loss at A=20*velocity head in 200 mm dia Head loss at…

Q: Q4: A turbine is located in pipe No.2, shown in figure (4). If the turbine efficiency is (90%), what…

Q: A pump draws water from reservoir A and lifts to reservoir B. Points 1 and 2 are points just before…

A: Given, Discharge, say Q = 15 L/s = 0.015 m3/s [1 m3 = 1000 L] Diameter of pipe at 1, D1 = 150 mm =…

Q: 7- a) b) c) d) For the transmission line shown below, what is the power of the pump with efficiency…

A: Efficiency, η=70% Flow rate, Q=200 lit./s The density of water, ρ=9806 N/m3 The slope of the…

Q: Find Hp of the turbine, (V=20 ft/s, * D=18 in , L=150 ft, f=O.03) Water 200 ft Turbine 20 tvs 200 ft…

A: ASKED: To determine the head of the turbine (Hp). Given, Head of water at the inlet of the pipe…

Q: sp. he pump in the system is 78% efficient and is rated 185 kW. Determine the energy added by he…

Q: Probiem 5: A liquid of specific gravity 1.7 flows in a 60-millimeter horizontal pipe. The total…

Q: omplete s

Q: 40gal/min of water is pumped and the energy loss in the discharge line is 13.5 feet and at the…

Q: Q2/ If the turbine extracts 400 kW from the flow, what flowrate must be passing through the system?…

A: L1=600 md1=0.6 mL2=600 md2=0.6 mf=0.020P1=P2=atmospheric pressureZ1-Z2=105-30=75V1=0Power of…

Q: W.S. EL 80 m B 10 cm diam. W.S. EL 0 A Pump EL- 6 m (Datum plane) (1) (2) 15 cm diam, FIGURE 5.16

Q: Water is flowing at a rate of 7 ft^3/s, and it is assumed that the head loss from the reservoir to…

A: What power must the pump supply in HP to allow this flow?

Q: Reservoir A and B located at 220 m and 100 m elevation respectively is connected by a 300mm diameter…

Q: A turbine is supplied with water from a reservoir which is 200 m above the level of the discharge…

A: Using the definition of fluid power and efficiency calculate the turbine head. Then using the…

Q: H-W1 Q1/ Neglecting losses, determine the discharge in Fig. below Oi so 075 Q2/When the pump in Fig.…

A: As per authoring guidelines, if the question number is not specified, the first question or three…

Q: If water is pumped from reservoir 1 to reservoir 2 through a 20 cm pipe with a length L1=70 m, and…

A: The expression for velocity in pipe is given as V=QA Substitute the value in above expression V=0.15…

Q: The pump is powered by a 30 kW motor. If the pump is 82% efficient, determine the pressure rise…

A: V1 = 40 m/s d1 = 4 cm =0.04 m d2 = 8 cm = 0.08 m effective power P = 0.82 x 30000= 24600 W

Q: A pump is rated with 80% efficiency and requires 4hp of power. The power output results to a…

A: Efficiency of the pump = QHρ367 P2 ρ=1000 kg/m3 P2= 2.9828 KW Velocity = 5ft/s=1.524 m/s Average dia…

Q: 630 cm^3/s Water at 320 k is PumPed in a 40 mm (id) through a length of 150m in horizontal direction…

A: Q = 630 cm3/sD = 40 mm L = 150 m H = 10 m = 0.00065 Pa-s

Q: 120 kPa 400 kPa Turbine D 9 cm D =3 cm Figure No.1 6:39 AMV/

Q: A closed cylindrical tank 5m high contains 2.5m of water. A 100mm diameter circular orifice is…

A: To find the air pressure above surface of water

Q: A pump drawing water from a reservoir and discharging it into the atmosphere at point B. The…

Q: Question 2 Oil (SG = 0.85) is flowing in a 10cm diameter pipe. The elevation of the pipe is 5m above…

A: Given:- Discharge in pipe = 30 l/s = 0.03 m3/s Diameter of pipe = 30 cm = 0.3 m Elevation above…

Q: The following figure and table contains the water levels of the reservoirs in the system and the…

Q: (67) The water tank shown is filled by pumping water from the well where the water level is located…

Q: through a pipe at 150 gradually in diameter from 165 mm at point M to 473 mm Water flows L/s that…

Q: Please answer asap and show all of your work

A: all the data assume for given diagram. i hope its helpfull.thank you.

Q: Q.23 Figure shows a lawn 40 cm sprinkier witn unequal arms. The jets issuing out of the sprinkler…

Concept explainers

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?

Question

Pump BC shown brings oil (SG = 0.72) to reservoir D at 170 L/sec. The energy lost from A to B is 1.1 J/N and from C to D is 4.7 J/N.
El. 84 m
D
EL 22.6 m
A
0.30-m Ø
B
El. 2.8m
How many hp does the pump supply the system?
O 108.164 hp
O 112.069 hp
O 150.228 hp
O 80.690 hp

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Medium lubricating oil (sg-D0.85) is pumped through 360m of horizontal 75mm pipe at the rate of 3.14L/s. If the drop in pressure is 300kPa. Compute for the absolute viscosity in Ns/m2 of the oil. a. 0.311 b. 0.206 C. 0.504 d. 0.790
2. A pump is used to transfer water from tank A to tank C through a pipeline that passes through point B. The AB pipeline experiences a head loss of 10m. Please, determine the power required by the pump and to draw an energy line that represents the state of energy of the water in the pipeline. It is assumed that any minor losses can be ignored, and the pump's efficiency is given as n=0.70. 50m A D₁-300mm L₁=1000m f=0.020 P B D₂=250mm L₂=2000m f 0.020 C 80m
Oil with sp. gr. of 0.87 is being pumped from a lower reservoir to an elevated tank as shown. The pump in the system is 78% efficient and is rated 185 kW. Determine the energy added by the pump. 160mm w EL. 200m 200mm 9 El.150m Oif. Sp.gr.=(0.82
Note: Don't copy from Chegg.
Read the question carefully and give me right solution according to the question
A four-stage (parallel) pump delivers 15 m3 1950 rpm. It is desired to construct a pump at a certain number of stages in series that should run at 1450 rpm delivering 18m/min with 280m of head in total. What should be the new diameter of the impeller and number of stages? per minute of liquid. The total head obtained is 27m. Initially, the impeller measures 24cm in diameter running at
the 9.63. When glycerin (25°C or 77°F) flows through a 30 m (100 ft) length of 75 mm (3 in.) pipe, the head loss is 36 m (120 ft). Calculate the flowrate. 9.64. A pump of what power is required to pump 40 1/min of crude oil from a tank of surface elevation 12 to one of elevation 18 through 450 m of 75 mm pipe, if the oil is at (a) 25°C, (b) 40°C?
The 600 mm pipe shown conducts water from reservoir A to a pressure turbine, which discharges through another 600 mm o pipe into tail race B. The head lost from A to 1 is 5 times the velocity head in the pipe and the head lost from 2 to B is 0.2 times the velocity head in in the pipe. If the discharge is 700 L/s A) Compute for the total head lost 1. 05: Compute for the extracted energy cause by the turbine Compute for the hp given up by the turbine. V Answer A) EL 60m 600 mm 1.63 m 58.37 m 537.3 hp 600 mm o B ▷ EL 0 m
Question is in figure
answer fast