A turbine is supplied with water from a reservoir which is 200 m above the level of the discharge pipe. The rate of flow through the pipeline is 250 liters per second. If the power output for the shaft of the turbine is 300 kW and it has a mechanical efficiency of 90 %. Calculate the head loss in the pipeline. Select one: O a. 20.2 m O b. 64.1 m O c. 45.9 m O d. 36.6 m

A turbine is supplied with water from a reservoir which is 200 m above the level of the discharge pipe. The rate of flow through the pipeline is 250 liters per second. If the power output for the shaft of the turbine is 300 kW and it has a mechanical efficiency of 90 %. Calculate the head loss in the pipeline. Select one: O a. 20.2 m O b. 64.1 m O c. 45.9 m O d. 36.6 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A small hydro electric power plant utilizing two (2) Pelton turbines and a single main penstock serving water to two nozzles for respective turbines. If both turbines are operated at the same time with same efficiency of 92% under the same net head of 2314 ft, same speed of 360 rpm and same flow rate. Determine the specific speed if the flow rate in the main penstock is 263 ft3 /s.
A centrifugal pump with an overall efficiency of 0.56 rotates at 1650 rpm. The flow is purely radial at the inlet of the rotor. The pump has the following characteristics: Flow rate Q = 72 L/s Inlet diameter D1 = 90 mm Outlet diameter D2 = 280 mm Head H = 25m Width at the inlet b1 =20 mm Width at the outlet b2 = 18 mm Leakage q = 2 L/s Mechanical loss Pm = 1.41 kW Blade angle at the outlet β2 = 35 ͦ The water density =998 kg/m^3,Atmospheric pressure 101 kPa a) Determine the hydraulic, mechanical and volumetric efficiencies. b)Determine the minimum number of blades required for the slip to not exceed 0.9. c)Determine the static pressure difference (P2-P1) through the impeller by using Bernoulli equation. d) Determine the available NPSH if the pump is placed 2m above the free surface of the tank and the vapor pressure is ?=2.43 ???.
A pipe is used to deliver water at a rate of 3.8 m³/s from the intake to the turbine. The difference in elevation between the intake’s water surface and the turbine is 200 m. Knowing the headloss in the pipeline from the intake to the turbine is 8 m, find the power (in kW) generated by the turbine if its efficiency is 80%.
2. A pump is used to transfer water from tank A to tank C through a pipeline that passes through point B. The AB pipeline experiences a head loss of 10m. Please, determine the power required by the pump and to draw an energy line that represents the state of energy of the water in the pipeline. It is assumed that any minor losses can be ignored, and the pump's efficiency is given as n=0.70. 50m A D₁-300mm L₁=1000m f=0.020 P B D₂=250mm L₂=2000m f 0.020 C 80m
An oil pump is drawing 18 kW of electric power while pumping oil with density 860 kg/m³ at a rate of 0.1 m³/s. The inlet and outlet diameters of the pipe are 8 cm and 11 cm, respectively. If the pressure rise of oil in the pump is measured to be 250 kPa and the motor efficiency is 95 percent, determine the mechanical efficiency of the pump. Take the kinetic energy correction factor as 1.05. Pump 8 cm D.cm ΔΡ = 250 kPa 18 kW Motor Oil 0.1 m³/s The mechanical efficiency of the pump is %.
Note: Use three decimal places and no need to input the unit. A 36-in-diameter pipeline carries oil (SG = 0.89) at 1 million barrels per day (bbl/day) (1 bbl = 42 U.S. gal). The friction head loss is 13 ft/1000 ft of pipe. It is planned to place pumping stations every 10 mi along the pipe. Estimate the horsepower which must be delivered to the oil by each pump. (in hp)
8. Energy Equation Water at the Lake William Dam enters a hydraulic turbine through a 30 cm diameter pipe at a rate of 0.6 m³/s and exits through a 25-cm diameter pipe. For the system, elevation effects are negligible and the pressure drop across the turbine is measured to be 148 kPa. For a combined turbine-generator efficiency of 83 percent, calculate (a) hurbine and (b) Wubrine- You look in the FE handbook and see: W turbine = 7/turbine-gen”ightutine, e turbine-genhtubine, e 30 cm diameter 25 cm diameter Turbine Generator
For the figure shown, water flows at a rate of 2.5 ft3/s and the total head loss is equal to 61 times the velocity head in the pipeline. Diameter of the pipe is 8 inches throughout its length. Calculate the power (in horsepower) provided by the pump. Round off your answer into a whole number. Answer: P = P hp 50 ft
At what speed, when pumping water, should the 105 cm pump of the figure below run to realize, at highest efficiency, (a) a head of 30 m? For this condition, what are the resulting (b) flow rate, and (c) brake horsepower? n=710 r/min 120 7.5 NPSH 6.0 105 105-cm dia. 4.5 3.0 90 96.5-cm dia. 75 89-cm dia. 86% 84% 45 1000 bhp 30 15 30 45 60 75 90 105 m/min por on NPSH, m 1500 bhp 1250 bhp %88 %88 • %08 %09 Total head, m
The pump draws oil with specific gravity of 0.90 from a reservoir and delivers it to the hydraulic cylinder. The cylinder has an inside diameter of 5.0 inch and in 15 seconds the piston must travel 20 inches while exerting a force of 11,000 lb. It is estimated that there are energy losses of 11.5 lb-ft/lb in the suction pipe and 35.0 lb-ft/lb in the discharge pipe. Both pipes are 3/8-in Scheulde 80 steel pipe with inside diameter of 0.423 inch. Calculate the pressure at the cylinder.
Energy Equation: Example 2: h₂ 80 m = Datum D = 0.2 m 0.02)V² 2g L = 2000 m- = 0.02 V² D2g A horizontal pipe carries cooling water at 10°C for a thermal power plant. The head loss in the pipe is hL Q = 0.06 m³/s where L is the length of the pipe from the reservoir to the point in question, V is the mean velocity in the pipe, and D is the diameter of the pipe. If the pipe diameter is 20 cm and the rate of flow is 0.06 m³/s, what is the pressure in the pipe at L = 2000 m? Assume a₂ = 1.
the 9.63. When glycerin (25°C or 77°F) flows through a 30 m (100 ft) length of 75 mm (3 in.) pipe, the head loss is 36 m (120 ft). Calculate the flowrate. 9.64. A pump of what power is required to pump 40 1/min of crude oil from a tank of surface elevation 12 to one of elevation 18 through 450 m of 75 mm pipe, if the oil is at (a) 25°C, (b) 40°C?