At what speed, when pumping water, should the 105 cm pump of the figure below run to realize, at highest efficiency, (a) a head of 30 m? For this condition, what are the resulting (b) flow rate, and (c) brake horsepower? 1710 t/min 120 NPSH 7.5 6.0 105 105-cm dia. 4.5 3.0 90 96.5-cm dia. 75 89-cm dia. 86% 84% 45 1000 bhp 30 75 90 105 Total head, m NPSH, m 1500 bhp 1250 bhp

At what speed, when pumping water, should the 105 cm pump of the figure below run to realize, at highest efficiency, (a) a head of 30 m? For this condition, what are the resulting (b) flow rate, and (c) brake horsepower? 1710 t/min 120 NPSH 7.5 6.0 105 105-cm dia. 4.5 3.0 90 96.5-cm dia. 75 89-cm dia. 86% 84% 45 1000 bhp 30 75 90 105 Total head, m NPSH, m 1500 bhp 1250 bhp

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Someone can help me with this one please
A volumetric tank 1.20 m in diameter and 1.50 m high was filled with oil in 16 minutes and 32.4 seconds. What is the average discharge? a. 100.5 L/min b. 102.5 L/min c. 103.6 L/min d. 108.7 L/min
Two reservoirs, A and B, are connected together by the two pipes with a pump between them. Assuming that the head loss in the pipes is given by hi = 0.015(L/d)(V/2g), where "L" is the length of pipe in feet and "d" is the pipe diameter in feet, determine (a) the velocity in each pipe, (b) the head added by the pump, and (c) the horsepower that must be supplied to the water to pump 2.5 cfs from the lower to the upper reservoir? El 140 ft B A El 90 ft L: = 2000 ft d: = 8 in. El 40 ft --- L; = 1000 ft d: = 8 in.
The water system in an urban area consists of an old 200 mm pipeline 750 m long which conveys water from a pump to a reservoir whose water surface elevation is 105 m higher than the pump. Water is pumped at a rate of 70li/sec. Determine the horsepower saved by replacing the old pipe with a new 25 cm pipe. Assuming f=0.033 and 0.022 for the old and new pipe respectively. Neglect other losses except frictional loss.
A single acting reciprocating pump has a plunger of diameter 250 mm and a stroke of 350 mm. If the speed of the pump is 60 rpm and it delivers 16.5 lit/sec of water against a suction head of 5 m and a delivery head of 20 m, what is the co- efficient of discharge?
A pump is being utilized to deliver a flow rate of 500 li/sec from a reservoir of surface elevation of 65 m to another reservoir of surface elevation 95 m. The total length and diameter of the suction and discharge pipes are 500 mm, 1500 m and 300 mm, 1000 m respectively. Assume a head lose of 2 meters per 100 m length of the suction pipe and 3 m per 100 m length of the discharge pipe. What is the required horsepower of the pump?(PLEASE INCLUDE DRAWING) USE BERNOULLI'S ENERGY EQUATION
At what speed, when pumping water, should the 105 cm pump of the figure below run to realize, at highest efficiency, (a) a head of 30 m? For this condition, what are the resulting (b) flow rate, and (c) brake horsepower? n=710 r/min 120 7.5 NPSH 6.0 105 105-cm dia. 4.5 3.0 90 96.5-cm dia. 75 89-cm dia. 86% 84% 45 1000 bhp 30 15 30 45 60 75 90 105 m/min por on NPSH, m 1500 bhp 1250 bhp %88 %88 • %08 %09 Total head, m
From the figure below, water must be pumped from the large tank below to the nozzle with an exit velocity of 5.8 m/s. The initial pump (Pump #1) that supplies 1.2hp of power to the water is not enough to produce the desired velocity. It is proposed that an additional pump (Pump#2) be installed as indicated to attain the desired value. Given the head loss for this flow is HL = 250Q^2, when Q is in m^3/s, determine the rated power (in hp) of Pump #2 if the mechanical efficiency of its motor is 86%. Nozzde Area = 0,01m² Pipe Area = 0.02m² v =5.8 Pump #1 Pump #2 2m !
A four-stage (parallel) pump delivers 15 m3 1950 rpm. It is desired to construct a pump at a certain number of stages in series that should run at 1450 rpm delivering 18m/min with 280m of head in total. What should be the new diameter of the impeller and number of stages? per minute of liquid. The total head obtained is 27m. Initially, the impeller measures 24cm in diameter running at
The following data refers to centrifugal pump for pumping water. Static suction head = 5 m; Length of suction pipe = 10 m Static delivery head = 20 m Delivery pipe length = 30 m Discharge = 1500 LPM Perform complete design of pump showing suitable layout.
5. It is desired to deliver 5 gpm at a head of 640 m in a single stage pump having specific speed not to exceed 40. If the speed is not to exceed 1352 rpm, how many stages are required?