Problem No. 2 A 250x400mm beam with a concrete cover of 40mm and stirrups of 10mm with fc' of 35Mpa and fy of 276Mpa. The reinforcement used has a diameter of 16mm. Calculate the following. 16. Based on the final number of reinforcements (adjusted), calculate the moment capacity of the beam 5 kN/m ↑ 10 KN ↑ 65 kN 20 kN/m z (m)

Problem No. 2 A 250x400mm beam with a concrete cover of 40mm and stirrups of 10mm with fc' of 35Mpa and fy of 276Mpa. The reinforcement used has a diameter of 16mm. Calculate the following. 16. Based on the final number of reinforcements (adjusted), calculate the moment capacity of the beam 5 kN/m ↑ 10 KN ↑ 65 kN 20 kN/m z (m)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Below is a trapezoidal beam with 3-28mm reinforcing bars at the bottom. Using the design properties of fc' = 21MPa, fs = 140MPa, n = 7, 50mm effective cover, determine the following: Note: Assume the beam has cracked. 650 50 500 ܘܘܘ 200 150 150 What is the flexural capacity of the beam Express your answer in KN-m.
concrete : C20 steel: S420 h=550 mm b=350mm steel rebars : 5Φ18
V. A simply supported reinforced concrete beam subjected the maximum shear force V=150KN. the section of the beam is rectangular with b×h=250mmx500mm.the concrete is of grade C30 (f=1.43N/mm², f=14.3 N/mm²) . The transverse stirrup is of HPB235 (f, = 210N/ mm? ) . It is required to design the web reinforcements of the beam only with stirrups.( 10mm, Ag = 78.5mm² ) a, = 35mm. nA SV1. No B. = 1.0, V = a f,bh, + fy · Data: C30 concrete (f=1.43N/mm², fe=14.3 N/mm²) HRB335 steel (f, = 300N / mm² ) HPB235 steel ( f, = 210N/ mm² ) ho=465
dont round off
Determine the minimum width "b" of the beam shown if the flexural stress is not to exceed 12 MPa. Answer must be in mm. Given: a = 1 m, b- 4 m. c= 2 m, P- 6 kN, and w = 3 kN/m. P kN 上 cm w kN/m (not scaled) 240 mm, a m bm Ri R,
Determine maximum shear and momentum of the beam load. Compute the value of the concentrated load. Using rule of thumb find initial size of beam Design a monolithic reinforced concrete Picture below for reference
Question 17
A wooden box beam is fabricated from four boards, which are fastened together with screws. Each screw can provide a resistance of 680 N. In service, the box beam will be installed so that bending occurs about the z axis, and the maximum shear force in the beam will be 11.6 kN. Assume d₁-44 mm, d₂=170 mm, b₁-150 mm, and b2-29 mm. Determine the maximum permissible spacing intervals for the screws. m d₁ X Answer: s= mm. b2 N b₁ d₂ d₁
Q1) The R.C slab system shown in Figure (1) supported by column line beams and carries a service live load of 5 kN/m and a service superimposed dead load of 3.5 kN/m in addition to its own weight. Slab thickness is 200mm, all beams are (300x600) mm. All columns are 300mm square, use f-25MPA and f=420MP.. According to the ACI-direct design method, determine the following: 6.0m 7.6m 6.0m (a) Design the middle strip bottom bars of the exterior indicated panel shown, in E-W direction. 6.0m 6.0m 7.6m (b)Design the required steel reinforcement at the exterior corner (C). Figure (1)
SHOW COMPLETE SOLUTION AND DRAW THE FBD.
Can you solve this please?