Problem 6.87 The journal bearings at A and B only support vertical forces. The allowable bending stress is oallo w = 173 MPa. (Figure 1) Figure 1 of 1 4 kN 3 kN 375 mm 375 mom 750mm

Q: If the applied load "P" causes the point C to be displaced downward by Sc=1 mm, determine the normal…

A:

Q: The bell-crank mechanism is in equilibrium for an applied load of P = 11 kN. Assume that a = 200 mm,…

A: Given Data  Determine the bearing stress in the bell crank at pin-B.

Q: *5-4 The copper pipe has an outer diameter of 40 mm and an inner diameter of 37 mm. If it is tightly…

A: Maximum shear stress is 26.73 MpaExplanation:Step 1: Step 2:

Q: h = 100 a.) Construct stress blocks which show the stresses acting on the cross-section at A and B…

A:

Q: Design the maximum permissible value of W using a factor of safety of 2, based on the following…

A: Given Data: The thickness of the support plates are 2 inches. The cross-section of the member is 6×2…

Q: The structure supports a distributed load of "w". The limiting stress in rod (1) is 380 MPa, and the…

A: We will find allowable load in rod and pin and take minimum of that value. We will take moment at C…

Q: The bell-crank mechanism is in equilibrium for an applied load of P= 15 kN. Assume that a = 300 mm,…

A:

Q: The steel pipe AB has a 64-mm outer diameter and a 5-mm wall thickness. Knowing that arm CDE is…

A:

Q: Determine the reactions of the beam. Please show step by step solution.

A: Please give helpful review

Q: 1-39 The lever is held to the fixed shaft using a tapered pin AB, which has a mean diameter of 6 mm.…

A: Given:Pin AB mean diameter,dm=6 mm

Q: 100 KUMT emm 130 1 5 m 25 kNm • At the top of the beam . At the neutral axis At the bottom of the…

A: Given: Required : At B, normal stress at top,  bottom and neutral axis  At A,  normal stress at…

Q: 5. Find the maximum bending stress. 6 kN A 1.0 m 1.2 m

A: calculate centroid for given figure…

Q: Prob. 1. The two aluminum rods support the vertical force of P-20 KN. Determine the requir diameter…

A:

Q: 4. The joint is fastened together using two bolts. The diameter of each bolt is 13.5 mm. Determine…

A: Given data in question  Load 80 kN Diameter 13.5 mm Width 30 mm Number of bolts 2 To find out…

Q: P6-5. Sketch the bending stress distribution over each cross section. (a) M P6-5 (b)

A: Two members cross section are shown in the above figure. We have to draw bending stress distribution…

Q: The steel pipe is supported on the circular base plate and concrete pedestal. If the normal failure…

A:

Q: PROBLEM 2 Strips A and B are to be glued together using the two strips C and D. a. Determine the…

A: force transfered by C strip = Force in D strip=force in A strip 2=20 KNlet the width of the strip C…

Q: 1. The shaft is subjected to the axial force of 40 kN. Determine a. the average bearing stress…

A: We have to find average bearing stress acting on collar and normal stress in the shaft and bearing…

Mechanics of Solids

It is the study of the behavior of solid materials, their characteristics under various circumstances such as variation in external forces, temperature, and other internal factors. It is one of most important study in the field of engineering science, especially chemistry and mechanical engineering. In rigid body, the idealization of the solid body in which deformation is neglected. Deformation is known as the force acting on the solid state system which exerts change in its shape of the body but it continues to be at rest or in a uniform motion but it cannot accelerate. But those solid systems do have elasticity, compressibility and can be bent. This field is very vast since there are wide range of materials around us.