Problem 4 only, solve carefully, include the units in every step and draw the diagram. Thanks!A steel tie rod on bridge must be made to withstand a pull of 5000 lbs. Find the diameter of the rod assuming a factor ofsafety of 4 and allowable stress of 14,000 ps 4. A steel tie rod on bridge must be made to withstand a pull of 5000 Ibs. Find the diameter of the rod assuming a factor ofsafety of 4 and allowable stress of 14,000 psi.5. A hollow shaft transmits 10 kW and running at 650 rpm with a shearing stress of 55 Mpa. The outside diameter is 1.2times that of the inside diameter. Find the inside and outside diameters in mm.6. Four cylinders rolling in opposite directions has a speed ratio of A:B.C:D = 5:2:3:4. If center distance between cylinderA and D is 80 inches, find the diameter of all cylinders.7. A steel 0.6 inch x 1.2 inch steel 90 m long is subjected to a 45kN tensile load along its length. If poison's ratio is 0.3.FindA. The deformation along its length, inchesB. The deformation along its thickness, inchesC. The deformation along its width, inchesD. The lateral strains, inches

Answered: Image /qna-images/answer/098754b1-ab4c-446f-b478-51f4c4529626.jpg

Problem 4 only, solve carefully, include the units in every step and draw the diagram. Thanks! A steel tie rod on bridge must be made to withstand a pull of 5000 lbs. Find the diameter of the rod assuming a factor of safety of 4 and allowable stress of 14,000 ps

Problem 4 only, solve carefully, include the units in every step and draw the diagram. Thanks! A steel tie rod on bridge must be made to withstand a pull of 5000 lbs. Find the diameter of the rod assuming a factor of safety of 4 and allowable stress of 14,000 ps

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

4. Schedule 40 pipe is to be used in a torsion application. The power applied is to be 200 hp and the pipe material is to be SAE 1141 OQT 900 steel. The loading is to be repeated. ( 400 RPM) Text book: Applied strength of Material 6th (a) Calculate the maximum allowable shear stress for the steel. (b) Calculate the smallest size of schedule 40 pipe
A pin connection, like that shown in Figure -16, is subjected to a force of 16,5 kN. Determine the shear stress in the 12.0 mm diameter pin.
) A machine having a mass of 9555 kg is supported by three solid steelrods arranged as showed in the following figure. Each rod has a diameter of 50 mm. Compute the stresses in MPa in the three rods of AB, BC, and BD.
Find the size of 14 bolts required for a CI engine cylinder head. The diameter of the cylinder is 400mm and the steam pressure is 0.12N/mne.Take the permissible tensile stress as 35MPa.
A pulley is keyed to a 28 mm steel shaft with a 7 mm x 8 mm x 20 mm key. If the hub length is 20 mm and the allowable crushing stress for the key material is 105 MPa, How much torque can be transmitted in kN-m?
3-103: A circular rod with a diameter of 10.0 mm has a groove cut to a diameter of 8.0 mm. A full radius of 1.20 mm is produced at the bottom of the groove. Compute the maximum stress in the rod when an axial tensile force of 5500 N is applied.
A punch for making holes in steel plates assumes that having a diameter of 0.75 in. is used to punch a hole in a 1/4 in. plate. If a force P=20,000 lb is required, what is the average shear stress in the plate and the average compressive stress in the punch?
x Question: The diameter of shaft used in the below design is 90 mm. Identical pulleys are used in the design with a radius of 160 mm. The forces acting on the system are defined as follow: F₁ = 1P kN; F₂ = 8P kN; F3 = 2P kN; F₁ = 6P kN; F5 = 4P kN; F = 7P kN. Employing the maximum shear stress theory, calculate the maximum permissible P for a safe design experience. L₁ = 1.4m; L₂ = 1.8 m; L3 = 1.4m; L4 = 1.6 m; allow = 75 MPa (allowable strength, σs) A F₁ F₂ L2 m F4 B 3 F6 Fs
Design of Machine Elements Assume you have a 30 mm in diameter AISI 1040 steel shaft welded on a rigid surface. Forces appliedto this shaft is given below. What would be length of the shaft considering the conditions as givenbelow;− 40 Nm torque is applied throughout the shaft (torque)− 100 kg load is applied at the end point of the shaft (bending)− 250 kg load is applied to push the shaft in the compression direction (normal force)− Factor of safety should be 2
Q3 The figure shows a round shaft from a gear transmission. Gears are mounted at points A, C, and E. Supporting bearings are at B and D. The forces transmitted from the gears to the shaft are shown, all acting downward. Compute the maximum stress due to bending in the shaft, accounting for stress concentrations. calculate the safety factor for the material selected.if martial 4150 OQT 1300 force 1 (f1)=9.5 kn ,Force 2(f2)=13.5Kn ,Force3 (f3)=18Kn
Q2: Steel tube having outer diameter of 80 mm is used to transmit 10 kW of power when turning at 50 rpm. The length of the tube is 1 m. - Task 1 - Task 2 Gsteet 75 GPa Determine the inner diameter d of the tube if the allowable shear stress is Tallow = 90 MPa. : Select an inner diameter and calculate the angle of twist at this power. 80 mm
A steel rod on a bridge must be made to withstand a pull of 6000 Ibs. Find the diameter of the rod in mm. assuming a factor of safety of 7 and ultimate stress of 62,000 psi (round off to whole number).