Two disks are connected by four rods, as shown in Figure P3–70. All rods are 6.0 mm in diameter and have the same length. Two rods are steel (E = 207 GPa), and two are aluminum (E = 69 GPa). Compute the stress in each rod when an axial tensile force of 11.3 kN is applied to the disks.

Two disks are connected by four rods, as shown in Figure P3–70. All rods are 6.0 mm in diameter and have the same length. Two rods are steel (E = 207 GPa), and two are aluminum (E = 69 GPa). Compute the stress in each rod when an axial tensile force of 11.3 kN is applied to the disks.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Three metal rods are firmly attached to the walls and the middle rigid plate. Rod AB is made from stainless steel and rods CD and EF are made from 2014-T6 aluminum. If a balanced load is applied to the rigid plate, determine what the stresses are in the rods. Follow the sign convention that tensile stress is positive and compressive stress is negative. The parameter values are listed in the table above the figure. A parameter value units 470 mm 400 mm 40 mm 30 mm 30 KN cc 080 BY NO SA 2021 Cathy Zupke L₁ L2 d₁ d₂ P 4₁ B C E The stress in AB σAB= The stress in CD and EF: OCD = EF= d₂ L₂ MPa D F MPa
Calculate the maximum load (P) that can be supported by the knuckle joint that shown in the figure below. The joint material has the following allowable stresses: tensile stress = compressive stress -50 Mpa, shear stress =35 Mpa and crushing stress = 90 Mpa. (Assuming: the load is applied statically). P- C1 78 mm C1 78 mm C2 C3 C3 156 mm 98 mm C4 C1 C5 C1 60 mm C4 C5 P. C5 C2
A rod of different materials is arranged as shown with the corresponding axial forces (see figure 3). Find the maximum value of the force P in kN such that it will not exceed a stress in steel of 140,000 kPa, in aluminum of 90,000 kPa, or in bronze of 100,000 kPa. INPUT THE NUMERICAL VALUE ONLY IN 3 DECIMAL PLACES
Explanation required, Don't directly paste the solution from other site⚠️
1. Find the tensile stress in MPa in member AB shown in the figure. All connection bars have square cross section and bar width is 15 mm. Points A, B and C are pin connections. Square 15 mm side 6m 3.5m C 20KN
indicate given, solution and box final answer
The figure shows a rigid bar that is supported by a pin at A and two rods, one made of steel and the other of bronze. Neglecting the weight of the bar, compute the force (in N) in the steel rod caused by the 42758-Nload, using the following data: length of steel = 1.27 m, length of bronze = 2.06 m Area of steel = 522 mm, Area of bronze = 239 mm Modulus of elasticity of steel = 216 Gpa, Modulus of elasticity of bronze = 84 Gpa x= 0.69 m, y = 1.08 m, and z = 0.86 m. Round off the final answer to three decimal places. ... Bronze Steel Ey te z
This is a subject of Strength of MAterials, COmpute exactly without shortcut.Show FREE BODY DIAGRAM and COMPLETE SOLUTION thank you
The two wooden boards shown in Figure are connected by a 0.5-in.-diameter bolt. Washers are installed under the head of the bolt and under the nut. The washer dimensions are D = 2 in. and d = 5/8 in. The nut is tightened to cause a tensile stress of 9,000 psi in the bolt. Determine the bearing stress between the washer and the wood. Bolt Washer ANSWER: D psi Washer Nut