Problem 3: Three steel bolts are to be used to attach the steel plate shown to a wooden beam. The plate will support a 110kN and the ultimate shearing stress for the steel used is 360MPA and that a factor of safety of 3.35 is desired, determine the increase in the bolt diameter required if an additional 100KN load is added to the existing 110kN.

Problem 3: Three steel bolts are to be used to attach the steel plate shown to a wooden beam. The plate will support a 110kN and the ultimate shearing stress for the steel used is 360MPA and that a factor of safety of 3.35 is desired, determine the increase in the bolt diameter required if an additional 100KN load is added to the existing 110kN.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Read the question carefully and give me right solution according to the question. Thank you
For this Problem, kindly refer to our Textbook, Steel Design Fifth Edition by William T. Segui. For Problem 8.2-3 Page 573, if the 65kip load (service load which is 30% deadload and 70% liveload) is changed to 85kips, and the 6inches distance is also changed to 6.1inches, using plastic analysis (LRFD) calculate the magnitude (only) of the shear force at the most stressed bolt due to eccentric load? Express your answer in kips in 2 decimal places.
SOLVE THIS PROBLEM USING THE SLOPE DEFLECTION EQUATIONS: A bolted connection shown is connected by 20 mm diameter bolts with an edge distance of 50 mm and the distance center to center of holes to be 75 mm. Assume that the deformation at bolt hole is a design consideration. The bolted connection is carrying an ultimate load Pu = 1500 kN, Fy = 248 MPa, Fu = 400 MPa and Fn = 415 MPa. Determine the following: (1) Design bearing strength of one bolt. (2) Design shear strength of one bolt. (3) The number of bolts are required for the connection show. P 12 mm plase P= I S00 kN 18 mm platr 12 mm plate
A steel plate (called a cover plate) having cross-sectional dimensions W2 8.0 in. x 0.7 in. is welded along the full length of the bottom flange of a W, 12.0 in. x 14.0 in. wide-flange beam (see the figure, which shows the beam cross section). I W2 cover plate What is the percent increase in the smaller section modulus (as compared to the wide-flange beam alone)? Round your answer to two decimal places. % in smaller section modulus =|
Centroid + Inertia 200 x 20 mm Plate The strength of the rolled section shown is increased by combining S section, channel, plate and then welded. 1. Determine the location of its centroid; and 5310 x 47.3 C310 x 30.8 2. Determine the moments of inertia of the composite section with respect to its centroidal x and y Semi-circle Weld, 10mm radius axes.
Pls answer both question, you'll get a like ty <33 Dont round off initial values, only round off in final answer ty
A steel plate is 300 mm wide and 40 mm thick is connected using 24 mm dia bolts of 3 numbers. The net sectional area of the plate is
Answer the following for the section at Point D Only Calculate the distributed load "w" that: Will cause the section crack Will cause the reinforcement to yield. Material Properties: F'c = 5000 psi Fy = 60000 psi Es = 29000000 psi Ln = 27 ft L wl₂² 16 wl,² 14 CD L wl,2 vl₁² 10 11 win² 16 h: 28 in A=4 in² b=14 in n d: 25 in
For the truss shown below identify zero force members. Make sure to state which joint you are looking at, which rules you are following and the zero force members. (When answering statement, start with "Looking @ joint... your case... are zero force members."
Determine the allowable strength of the figure as shown
Subject: Steel design- Bolted Steel Connection *Use NSCP 2015 formula/guide to solve this problem *Use Handwritten
Determine the available strength of the compression member shown in figure below.