Problem 3: Now we will repeat the previous problem using the Cartesian method. Values: ● FA = 20 N FB = 30 N ● α = 25° Use the Cartesian method to determine... a) the magnitude of the resultant force on the bolt. b) the angle made by the resultant, as measured relative to the positive x-axis. FA α FB

Problem 3: Now we will repeat the previous problem using the Cartesian method. Values: ● FA = 20 N FB = 30 N ● α = 25° Use the Cartesian method to determine... a) the magnitude of the resultant force on the bolt. b) the angle made by the resultant, as measured relative to the positive x-axis. FA α FB

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Thumbs-up will be given. Write the complete solutions legibly. No long explanation needed. Solve in 3 decimal places. Box the final answer.
MODULUS OF ELASTICITY= 15x10^6
please show all your solutions I NEED IT ASAP PLEASE
A concentrated load P = 5 kN, acting downwards, is located midway between the simple supports of the beam shown. Determine the deflection, in mm, at the free-end C. Use a = 6 m., E = 239 GPa, and I = 271 x10^6 mm^4. ROUND OFF TO THREE DECIMAL PLACES. USE STORED VALUES. INCLUDE THE SIGN OF YOUR FINAL ANSWER. (positive = upwards; negative = downwards) A a a
Problem 2 For the simply supported beam shown below, determine whether the beam is cracked or un-cracked under the applied loads, use f'e = 25 MPa, if the beam is cracked calculate the bending stresses in the beam using the transformed area method. 20 KN 300 mm 4 kN/m A↓ D 3025 k 3 m 3 m 500 mm - աա St
Solve the given problem. Round off answers in all computations in 4 decimal places. Determine the moment capacity of the beam shown in the figure.
Beam AB (A = left support, B = right support) is loaded with a concentrated load (P = 500 N) and a moment (100 N-m). Use a = 1 m. What is the value of the deviation of B relative to the tangent drawn at A? Round off to two decimal places.
Use the diagram shown above. Given • D₁ = 8 ft . • D₂ = 6 ft D3 = 3 ft W = 100 #/ft D3 • P= 200 # Solve for the internal moment at X. D₁ D 2 X W P Note: Enter the numerical value only for your calculation results. You'll be asked to specify the unit for your calculation result in the following question. (This is due to Canvas' lack of ability to require units for calculation question.)
A beam is loaded and supported as shown. (a) Use the double-integration method to determine the reactions at supports A and B. (b) Draw the shear-force and bending-moment diagrams for the beam. (c) Determine the deflection in the middle of the span. Assume w = 11 kN, L = 7.4 m and El - 6.9 x 104 kN-m2 is constant for the beam. V. L.
Using Tall = 68 MPa and G= 27 GPa, determine for each of the aluminum bars shown the largest torque T that can be applied and the corresponding angle of twist at end B. Refer to Table 3.1. (a) (b) 45 mm 15 mm 25 mm 25 mm 900 mm B Check my work B The largest torque that can be applied at end B of bar a is N-m and the corresponding angle of twist is The largest torque that can be applied at end B of bar bis N-m and the corresponding angle of twist is
Compute the maximum deflection for the cantilever beam as shown below. Use conjugate beam method. Show complete solution and illustration.
1. A simply supported beam carries three concentrated loads as shown in the figure. a. Determine the slope and deflection equation for every segment of the beam. b. Determine the deflection per El at the right half of the beam. (hint: Eq. - Ely = 54x-2/3x³-5/3[x-67³-6264) c. Determine the value of Ely under the 8-kip load. (Ans: 6246 kip.ft³) 10 kips 8 kips 6 ft 6 ft 6 ft 10 kips 6 ft