12'-0" TYP. 6 3 10 12 13 www 19 20 17 8 18 12'-0" TYP. 14 45 P 21 16 Use the diagram shown above. Given P= 300 # Calculate the magnitude of the internal force in Member 18. (Magnitude is a positive value.) Note: Enter the numerical value only for your calculation results. You'll be asked to specify the unit for your calculation result in the following question. (This is due to Canvas' lack of ability to require units for calculation question.)

12'-0" TYP. 6 3 10 12 13 www 19 20 17 8 18 12'-0" TYP. 14 45 P 21 16 Use the diagram shown above. Given P= 300 # Calculate the magnitude of the internal force in Member 18. (Magnitude is a positive value.) Note: Enter the numerical value only for your calculation results. You'll be asked to specify the unit for your calculation result in the following question. (This is due to Canvas' lack of ability to require units for calculation question.)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The caster unit is subjected to the pair of 84-lb forces shown. Determine the moment associated with these forces. The moment is positive if counterclockwise, negative if clockwise. | 1.3" |—— 84 lb Answer: M- i 84 lb lb-in.
In (Figure 1), F = 750 N. Point B is located at the midpoint of the rod. Figure 6 m 4 m D F 4 m B 3 m 4 m 1 of 1 Part A Determine the component of F that act along rod AC. Express your answer to three significant figures and include the appropriate units. F|| = Submit ▾ Part B for Part A for Part A undo for Part A redo for Part A reset for Part A keyboard shortcuts for Part A help for Part A FL= Value Determine the component of F that act perpendicular to rod AC. Express your answer to three significant figures and include the appropriate units. Submit Units Request Answer for Part B for Part B undo for Part B redo for Part B reset for Part B keyboard shortcuts for Part B help for Part B Value Units Provide Feedback Request Answer
GIVEN: Bars A and C are made of steel and bar B is made of brass. Each bar has a cross-sectional area of 4 in? Esteel = 30 x 10° ksi Ebrass = 15 x 10³ ksi REQ'D: The force in the brass bars and the forces in the steel bars when P = 10 kips Lo003 in.gap 18 in. steel sleel Ass
Problem 8.61 Part A The two blocks used in a measuring device have negligible weight. The spring is compressed 4 in. when in the position shown. The end of the screw is smooth and the coefficient of static friction at all other points of contact is μ= 0.29. (Figure 1) Determine the smallest axial force P which the adjustment screw must exert on B in order to start the movement of B downward. Express your answer to three significant figures and include the appropriate units. Figure k = 20 lb/in. A 60° 45° B 1 of 1 P= Value Submit Request Answer Provide Feedback ? Units
VI IN Determine the force in each member of the truss. State if the members are in tension or compression. Take that P = 470 lb .(Figure 1) Submit Request Answer Part E Determine the force in the member AB of the truss, and state if the member is in tension or compression. Figure 1 of 1 Express your answer to three significant figures and include the appropriate units. Assume positive scalars for members in tension and negative scalars for members in compression. B μΑ ? 3 ft FAB = Value Units Submit Request Answer -2 ft -2 ft Next >
3. The small sphere shown below has held by two wires with tension To. sphere is released from equilibrium. Determine the ratio To/T1, where T1 is the tension in the remaining wire immediately after the other mass of 2kg. It is initially One wire is cut and the small a one is cut. 30 30
The beam cross section shown below has been proposed for a short pedestrian bridge. The cross section will consist of two pipes that are welded to a rectangular web plate. Dimensions of the cross section are: h = 470 mm tw = 14 mm d = 120 mm t = 9.6 mm Additionally: • The area of each pipe is A = 3330 mm2. • The moment of inertia of the entire beam cross section about the z centroidal axis is IZ = 428040000 mm4. If the beam will be subjected to a shear force of V = 225 kN, determine the shear stress at point H, located at yH = 110 mm above the z centroidal axis.
Verify the given moment(s) of inertia and find and y. Assume that each lamina has a density of p = 1 gram per square centimeter. (These regions are common shapes used in engineering.) = y= Right triangle b 4₁=1 bh³ 1₁ = 1/2b³h
A frame has dimensions and loadings as shown in the figure and parameter table. Determine the horizontal and vertical support reactions that the pins exert on the frame at A and C. Take postive directions to be to the right, and up. 080 BY NO SA 2021 Cathy Zupke parameter Force Ax Force Ay= Force Co = Force Cy= = W L₁ L2 A value 1 3 4.5 -L₂- units kN/m m m KN KN KN KN C B W
For the frame shown below, what is the value of the force in member BC? (Note: enter your numeric answer only. No need to enter units. Give your answer to two decimal places). FBC = N 1.2 m 0.1 m 0.3 m В C 0.6 m 50 kg А