Problem #3 lo lag An eccentrically loaded continuous foundation is shown in (Eccentricity in one direction only) e = 0.15 m I Qall Y = 17 kN/m³ c' = 0 4'= 36° the figure. Determine the maximum allowable load (Qall) 1.0 m that the foundation can carry. Use Meyerhof's effective area method and FS of 4. B = 2 m Solution: Centerline

Problem #3 lo lag An eccentrically loaded continuous foundation is shown in (Eccentricity in one direction only) e = 0.15 m I Qall Y = 17 kN/m³ c' = 0 4'= 36° the figure. Determine the maximum allowable load (Qall) 1.0 m that the foundation can carry. Use Meyerhof's effective area method and FS of 4. B = 2 m Solution: Centerline

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Repeat Problem 4.8 using Prakash and Saran’s method.

A: Given; Eccentricity, e=0.15m Unit weight of soil γ=17kN/m3 Cohesion (c')=0 ϕ' (friction…

Q: A 2.0 m wide square foundation is placed at 0.5 m depth in a saturated clay where c = 40 kN/m² and y…

A: Width of the foundation (b) = 2 mDepth of the foundation (h) = 0.5 m Cu = 40 kN/m2Unit weight = 19.0…

Q: a) Find the allowable load on the foundation by Terzaghi method, assuming a general shear failu with…

A: AnswerNet allowable load = Qall Cohesion C =13 kpaDry Unit weight of soil () =17 Kn/m3Saturated Unit…

Q: 12.4

Q: For a square foundation, according to the information given and the assumption of vertical load, it…

Q: Use Meyerhof's equation

A: i hope its helpfull.thank you.

Q: A square foundation must withstand an allowable load of 1805 kN with reliability of 3. With the…

Q: A 1.5 m wide continuous foundation carries a wall load of 375 kN/m on a clayey soil where y = 18…

A: Width of footing, Depth of footing, Wall load, Bulk unit weight, Cohesion, Angle of friction, To…

Q: 4.6 For a square foundation that is B X B in plan, D, = 2 m; vertical gross allowable load, Qall =…

Q: According to the given information, it is desirable to determine the net allowable tolerable load by…

Q: A shallow foundation measuring 1.75 mx 1.75 m is to be constructed over a layer of sand. Given: D,=1…

A: footing size=1.75×1.75 m Df = 1m N¯60= 10 q=120 kN/m2 To calculate = elastic settlement of the…

Q: A rectangular foundation 2 meters long and 4 meters wide is located on the surface of a sloping…

A: Hansen's method is used to find the ultimate bearing capacity of the soil. Hansen's method is…

Q: The shallow foundation is shown in Figure 4.24 measures 1.5 m X 2.25 m and is subjected to a centric…

A: Given :

Q: A square foundation is 1.5 m x 1.5 m in plan. The soil supporting the foundation has a friction…

A: Given: The size of the square footing is 1.5 m x 1.5 m. The depth is 1 m. The unit weight of the…

Q: Mat foundation (20 x 30) is built on a sand layer with an internal friction angle of 32 degrees and…

A: Answer We know that Vesic's bearing capacity equation is given by q = C' Nc sc dc ic + γ*df*Nq sq dq…

Q: The ultimate load, Qu (assume two-way eccentricity) for a square foundation as shown in Figure, with…

Q: A square foundation with a depth of 1.5 m will carry a load of 3000 kN. Soil has a property index of…

Q: A square foundation is 3mx3m in plan. The soil supporting the foundation has a friction angle of Phi…

A: A Square foundation of 3mx3m.Friction angle of Phi = 21 degreesC' = 22KN/m2Depth of foundation (Df)…

Q: A square foundation is 1.5 m X 1.5 m in plan. Given the soil properties supporting the foundation…

Q: An eccentrically loaded foundation is shown in Figure P3.9. Use FS of 4 and determine the maximum…

Q: A continuous foundation is shown. If the load eccentricity is 0.2m, determine the ultimate load, Qu,…

A: e = 0.2m B = 2m Df =1.5m It has been asked in the question to determine the Ultimate load QU.…

Q: The load on the square foundation with a vertical axis has an angle of 15 degrees. Based on the…

A: According to the general formula, the allowable tolerable load can be determined by the following…

Q: An eccentrically loaded foundation is shown in Figure 12.25. Determine the ultimate load Q that the…

A: Solution attached below

Q: A square column foundation has to carry a gross allowable load of 1805 kN ( FS = 3). Given: D f =…

A: Given: The load on the column is 1805 kN. The factor of safety is 3. The depth of the footing is 1.4…

Q: the foundation can carry. Use Meyerhof's effective area method.

A: Use meyerhof's effective area method To find Maximum allowable load

Q: A square foundation must withstand an allowable load of 1805 kN reliability of 3. With the given…

Concept explainers

Load and resistance factor design

Load and resistance factors design (LRFD), also known as Limit state design (LSD), refers to the design method used in building engineering. A boundary condition is a condition of a structure where it can no longer meet the relevant design requirements. The condition may refer to the load level or other actions on the structure, while the terms refer to the integrity of the structure, suitability for use, durability, or other design requirements. A structure designed for LRFD is limited to keeping track of all possible actions during its design time and is always ready for use, with the appropriate level of reliability in each boundary condition. LRFD-based construction codes clearly define the appropriate levels of reliability in their instructions.

Question

Problem #3 lơ lag
An eccentrically loaded continuous foundation is shown in
(Eccentricity in
one direction only)
e = 0.15 m
I Qall
y = 17 kN/m³
c' = 0
4'= 36°
the figure. Determine the maximum allowable load (Qall)
1.0 m
that the foundation can carry. Use Meyerhof's effective
area method and FS of 4.
B = 2 m
Solution:
Centerline

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Geotechnical
1) (30 points) Find the stress beneath Point B of the 40 ft by 80 ft. L-Shaped flexible mat foundation at depth (Z) = 20 ft. deep. Mat load is 200 psf. 80' 20 200 psf 1401 20 60
A 2.0 m wide strip foundation is placed in sand at 1.0 m depth. The properties of the sand are: = 19.5 kn/m3, c’ = 0 and ’ = 34. Determine the maximum wall load that the foundation can carry, with a factor of safety of 3.0, using Meyerhof’s modified bearing capacity equation with appropriate factors
An eccentrically loaded continuous foundation is shown in Figure P6.18. Determine the ultimate load Qu per unit length that the foundation can carry. Use the reduction factor method [Eq. (6.67)]. 4 ft 2 ft Figure P6.18 Qu 2 ft → -5 ft Y = 105 lb/ft³ Groundwater table Ysat 118 lb/ft³ c' = 0 $' = 35° =
Use Terzaghi's equation and Terzaghi's Table
A square foundation is shown in Figure P6.19. Use FS = 6,and determine the size of the foundation. Use Prakash and Saran's method [Eq. (6.59)].
According to the form and assumption of reliability coefficient 4, it is desirable to determine the allowable load tolerable by the foundation. (Eccentricity in one direction only) 0.1 m y= 17 kN/m e = 0 d'= 32° 0.8 m 1.5 m X 1.5 m Centerline