Problem 3: A cylindrical block of concrete is 30 cm long and has a circular cross-section of 10 cm diameter, figure 2-7. It carries a total compressive load of 70 kN, under this load contracted 0.02 cm. Estimates the average compressive stress over a normal cross-section and the compressive strain. 70 kN 10 cm diameter 30 cm long 70 kN

Problem 3: A cylindrical block of concrete is 30 cm long and has a circular cross-section of 10 cm diameter, figure 2-7. It carries a total compressive load of 70 kN, under this load contracted 0.02 cm. Estimates the average compressive stress over a normal cross-section and the compressive strain. 70 kN 10 cm diameter 30 cm long 70 kN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Answer it correctly!
A RECTANGULAR ALUMINUM BLOCK IS 110mm LONG IN THE X DIRECTION, 70mm WIDE IN THE Y DIRECTION AND 85mm THICK IN THE Z DIRECTION. IT IS SUBJECTED TO A TRIAXIAL LOADING CONSISTING OF A UNIFORMLY DISTRIBUTED FORCE OF 210 KN (COMPRESSION), 170 KN (TENSION) AND 230 KN (COMPRESSION) IN THE X, Y AND Z DIRECTIONS RESPECTIVELY. IF THE POISSON'S RATIO = 1/4 & E= 72 GPa, DETERMINE THE STRAINS IN THE X, Y AND Z DIRECTIONS. ALSO DETERMINE A SINGLE DISTRIBUTED FORCE IN THE Y DIRECTION THE WOULD PRODUCE THE SAME Z DEFORMATION AS THE ORIGINAL.
A concrete column reinforced with steel rods has a square section of 250 mm by 250 mm and can support a load of 700 KN. Calculate the minimum number of steel rods if each will have a diameter of 6 mm which will be needed if the stress is not to exceed 8 x 106 N/m2 . The elasticity of the steel is 200 x 109 N/m2 and concrete is 12 x 109 N/m2 .
Determine the tensile steel ratio of a singly reinforced concrete beam for the following conditions using concrete strength f’c = 21 MPa and steel yield strength fy = 420 MPa. if the tensile strain is set as 0.009 upon crushing of concrete at a strain of 0.003. = [rr] (5 decimal places)
A 150mm diameter cylindrical concrete specimen was tested for compressive strength. What would be the maximum applied force in kN when the stress at failure is 41.4 MPa?
PROBLEM TO SOLVE: 600 mm 400 mm Using fe' = 28 MPa, Mmax = +320 kNm Determine the following: a. Cracking Moment (kNm) 6-25mm diam. b. Compressive Stress felt by concrete (MPa) c. Tension Stress felt by the tension bars (MPa)
What would be the average compressive strength of concrete if the load at failure of the 3 trials are 55, 100 kg, 54, 800 kg, and 55, 200 kg. Diameter of the sample is 6”. a 31.1 MPa b 30.1 MPa c 30.6 MPa d 30.6 MPa
Using Figure 4, a cross-section of a concrete beam, answer the questions that follow.5.1. Calculate the moment of inertia about the X-axis and the Y-axis 5.2 Calculate the combined bending and direct stress at points A, B and C. All loading is assumed to compressive. revision paper 2020
Using a simply supported pre-stressed concrete beam, explain the following status using stress diagrams: Stress condition due to pre-stress alone. Change of stress conditions due to the increment of external load: Decompression moment (bottom fibre compression = 0); Cracking moment (tensile strength develops at the bottom and starts cracking at the bottom); and Balance state (whole section is at an equal amount of compression).
Strength of Materials Answer should be 0.378 x 10-3 m2 ; 13.02 kN/m :) A concrete beam of rectangular section is 10 cm wide and is reinforced with steel bars whose axes are 30 cm below the top of the beam. Estimate the required total area of the cross-section of the steel if the maximum compressive stress in the concrete is to be 7.5 MN/m2 and the tensile stress in the steel is 135 MN/m2 beam is subjected to pure bending. What bending moment would the beam withstand when in this condition? Assume that Young's modulus for steel is 15 times that for concrete and that concrete can sustain no tensile stresses.
Referenced concrete Using inner, not outer, triangles On the below
A 150mm x 150mm concrete specimen was tested for flexure strength over a span of 600mm. The load at midspan causes a flexure strength of 41.4 MPa. What was the maximum applied load in kN?