Problem No. 2: The cross-section of the 8-m long simply supported beam is shown below. If the concrete has f. = 21 MPa, f, = 414 MPa and the unit weight of concrete is 23.5 kN/m’, compute the following: a. The cracking moment and the uniform load that the beam could carry in addition to its self-weight. b. The bending moment and the uniform load that the beam could carry in addition to its self-weight using transformed area method. c. The nominal moment and the uniform load that the beam could carry in addition to its self-weight. 375 mm 2– 25 mm 600 mm 75 mm| 150 mm 250 250 mm mm

Problem No. 2: The cross-section of the 8-m long simply supported beam is shown below. If the concrete has f. = 21 MPa, f, = 414 MPa and the unit weight of concrete is 23.5 kN/m’, compute the following: a. The cracking moment and the uniform load that the beam could carry in addition to its self-weight. b. The bending moment and the uniform load that the beam could carry in addition to its self-weight using transformed area method. c. The nominal moment and the uniform load that the beam could carry in addition to its self-weight. 375 mm 2– 25 mm 600 mm 75 mm| 150 mm 250 250 mm mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Please try to solve only 1st two parts
#2 will answer. Please use correct DECIMAL PLACES and UNITS. Thanks
0.19L
2.From the figure below; bending moment of 8 KN-m. The normal weight of concrete has an fc' of 26.4 MPa. solve and show the complete solution and pick the correct ans
A pre-tensioned rectangular concrete beam 200 mm wide and 350 mm depth is prestressed with three straight tendons, each having a cross-sectional area of 60 mm2 to an initial stress of 1100 N/mm2. The tendons are located at 90 mm from the soffit of the beam. If modular ratio is 6, then the loss of prestressing force (in kN, upto one decimal place) due to the elastic deformation of concrete only is
The properties of the reinforced concrete beam are b = 306 mm, d = 467 mm, Ast = 1007 mm2, and Est / Eco = 10. If the working stresses are 19.1 MPa for concrete and 102.2 MPa for steel, determine the largest bending moment (in Nm) that may be applied safely.
A concrete beam of rectangular cross-section of 200 mm x 400 mm is prestressed with a force of 400 kN at an eccentricity 100 mm. The maximum compressive strength in concrete is
I will dislike for wrong answers solve carefully
Problem 4.35 A Part A Column AB is made from high strength pre-cast concrete and reinforced with four in. diameter A-36 steel rods. The allowable normal stress for the high strength concrete and the steel are (allow) con = 1.8 ksi and (allow) st = 24 ksi, respectively. The modulus of elasticity for high strength concrete is 4.2 × 103 ksi and for A-36 steel is 29 × 103 ksi. (Figure 1) Determine the magnitude of the maximum allowable floor loading P. Express your answer to three significant figures and include the appropriate units. ΜΑ Pmax = 132 kip ? Figure 10 ft B a < 1 of 1 Submit Previous Answers Request Answer X Incorrect; Try Again; 4 attempts remaining Provide Feedback 9 in. 9 in. Section a-a
please answer (e)
Three high-strength concrete poles, with an effective cross- sectional area of 40, 000m * m ^ 2 and a length of 2 m, support a stiff steel plate. The center post is 1 mm shorter than the others before the load P is applied. If the concrete's allowed compressive stress is 20 MPa, calculate the maximum load that can be carried. E = 30GPa for concrete
In a pre-stressed concrete beam section shown in the figure, the net loss is 10% and the final pre- stressing force applied at X is 750 kN. The initial fiber stresses (in N/mm2) at the bottom of the beam were: d₁ d₁ b X મ ય ય ના તા b = 250mm d, = 200mm d₂ = 100mm Id₂