Problem 2.22 Compute the allowable resisting moment of the section shown using the transformed area method if allowable stresses are f= 1800 psi, f, f = 24,000 psi, and n = 8. 12 in.- 1 #10 2 in. 2 in. 2 #10 -10 in.- 4 in. 4 in. 16 in. 12 in. 12 in. 4 in.

Problem 2.22 Compute the allowable resisting moment of the section shown using the transformed area method if allowable stresses are f= 1800 psi, f, f = 24,000 psi, and n = 8. 12 in.- 1 #10 2 in. 2 in. 2 #10 -10 in.- 4 in. 4 in. 16 in. 12 in. 12 in. 4 in.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: For the beam and loading shown, consider section n-n and determine the shearing stress at a) point…

A: Given data : We are asked to determine the shearing stress at A ) Point a B ) Point B

Q: Analyze the frame shown below using Portal Method.

Q: Forces are applied at points A and B of the solid cast-iron bracket shown. The bracket has a…

Q: 32 A beam which is composed of concrete and a wide flange steel is subjected to moment M = 1126…

A: Given: A composite beam made up of steel and concrete having Compressive stresses to be carried by…

Q: Design a reinforced concrete beam with a balanced stress reinforcement that will resist a bending…

A: Given: Bending moment = 140 kN.md = 1.5 bfc = 12 MPafs = 160 MPan = 8

Q: Three loads are applied to the short rectangular post shown. The cross-sectional dimensions of the…

A: Given data: F1 =104 KN F2 =193 KN F3 = 61 KN

Q: By internal couple method, what is the maximum stress on the steel side of the transformed section?…

A: Given data: m=9

Q: An unequal angle section 200 mm x 150 mm x 15 mm is to be used in a truss as a strut of length 4.5…

Q: Q.No.3: Determine the ACI design moment capacity =60000 psi. Also draw the strain diagram? 4 #9 bars…

Q: For the steel truss and loading shown, determine the magnitude of the deformation (in inches) of…

A: Tanθ=yx=7.912.4=32.50°cosθ=0.8433sinθ=0.5372x=12.4ft=12.4×12=148.8inchy=7.9ft=7.9×12=94.8inchLength…

Q: A wooden beam is fabricated from one 2 × 16 and two 2 × 10 dimension lumber boards to form the…

A: The given data is: A1=16*6=32 in2 y1=10+(2/2)=11 in A2=10*4=40 in2 y2=1/0/2=5 in

Q: Calculate the stresses in members AB, AC, and BC if the cross-sectional area of each member is 1200…

A: in ∆ABCsinθ=35 and cosθ=45where,θ=angle made by the member AC with the verticalthen from…

Q: Determine the following: a. AE [Select] b. CE [Select] С. CD [ Select ] P. 40 kN 3 m F 20 kN 20 kNE…

Q: Two vertical forces are applied to a beam of the cross section shown. Determine the maximum tensile…

Q: A doubly reinforced beam, which have a base of 310 mm, and an effective depth of 410 mm, is…

A: To Find - b) What is the value of fs' (actual stress of the compression bars)

Q: The continuous beam and post system shown below supports a 10 kip vertical load and a 5 kip…

A: The moment and shear force will act at point B. Moment and shear will be caused due to force of 5…

Q: For the beam shown, calculate the magnitude of the maximum compressive bending stress (in psi) if P…

Q: A 7.3 m B C 2 6.4 kN 8.0 kN D 1.9 m - 4.0 m

A: The truss is analyzed with the help of equilibrium equations The sum of vertical forces is equal to…

Q: Compute the bending stresses in concrete and steel of the doubly reinforced beam section given in…

A: Given: b=16in.d=32ind'=2.5inAS=6.24in2AS'=2.37in2fc'=4000psify=60000psiCalculate the value of…

Q: For the steel truss and loading shown, determine the deformation (in inches) of member BD, knowing…

A: First calculate the member force in BD using the method of sections. Then using the HOOKES formula…

Q: Given: A and B are both made of wood and are 40 in. thick, the ultimate shear stress for the wood…

A: Ultimate shear stress: It is defined as the maximum stress that can allow the material or an object…

Q: The steel frame shown has a diagonal brace BD with an area of 1780 sq.mm. Determine the largest…

A: Check Determinacy In this given diagram there are four support reactions, RA , HA, RD Since D is a…

Q: Check the midspan deflection of the W12 x 40 girder shown? Neglect the weight of the girder. Assume…

Q: For the beams of the cross section shown, calculate the nominal moment (Mn) and check the tensile…

Q: Two steel plates are welded together to form an inverted T-beam and are loaded as shown below.…

A: We know that Bending stress is given by σ = MI*y For Maximum bending stress we can write σmax =…

Q: 1. For each of the following, assume a rectangular cross section with tension steel only and…

Q: by: e integration method 10 kN ay Method A nt area method

A: Hi! Thank you for the question As per the honour code, We’ll answer the first question since the…

Q: 1. Calculate the bending stresses in the beam using the transformed area method. Use a concrete…

A: Bending stress is the particular type of normal stress when the beam or any other structure which…

Q: 5) For the truss below, compute the horizontal deflection of point C using virtual work under the…

A: A truss could be a structure in engineering that "consists of two-force members only, with the…

Q: The beam is made from southern pine and is supported by base plates resting on brick work. (Figure…

A: Given: Required : Length of base plate at A and B

Q: Determine the smallest allowable cross-sectional area in square millimeters of member CE of the…

A: Bridge Type:The image depicts a Pratt truss bridge design. This is a common type of truss bridge…

Q: What is the total elongation of steel bar having a diameter of 2 in. hanging over with a length of…

Q: SITUATION. Based on the figure shown a hallow steel pipe with external diameter Do of 200mm has a…

A: Given- P=500 kN Outside diameter, D0=200 mm Length, L=3 m E=200GPa Required to determine the inner…

Q: A doubly reinforced beam, which have a base of 310 mm, and an effective depth of 410 mm, is…

A: Beam can be characterized as an underlying part which conveys every upward burden and opposes it…

Q: AW18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P= 27 kips, w…

Q: The axial force in the column supporting the timber beam shown is P = 24 kips. Determine the…

Q: e "transformed section method". sample problem: The cross-section shown below is a rectangular…

A: Given: -fs=138MPaf'c=20MPan=124-25mm diameterTo find:-wether safe or not

Q: A doubly reinforced beam, which have a base of 310 mm, and an effective depth of 410 mm, is…

A: The values given in the question are as follows: Width of beam(b)=310 mm Effective depth of…

Q: te the flexural stress (MPa) in the concrete for the beam shown using transformed-area 1. Area of…

Q: A rectangular beam has a width of 280 mm and an effective depth of 500 mm. It has a reinforcement…

A: Given: The width of the beam is 280 mm. The effective depth is 500 mm. The area of reinforcement is…

Concept explainers

Beams

In structural engineering, a beam is a component made of a variety of materials (including steel alloys, and wood) that can resist loads applied laterally to the beam axis. Members, elements, rafters, shafts, and purlins are all terms used to describe beams.

Question

O T☺ 1
Problem 2.22 Compute the allowable resisting moment of the
section shown using the transformed area method if allowable
stresses are f = 1800 psi, f, = f = 24,000 psi, and n = 8.
12 in.
1 # 10
12 in.
mum <
(1
|||
2 #10
-10 in.
●
4 in.
2 in.+
4 in. 16 in.
(-AST 25. maldos
$2 in.
4 in.
12 in.
مزر للأعلى لاستعراض الفلاتر
إضافة شرح..
×

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The steel frame shown has a diagonal brace BD with an area of 1910 sq.mm. Determine the largest allowable load P (in N) if the change in length of member BD is not to exceed 1.38 mm. Use x = 4.51m, y = 5.75m, and E = 197.5 Gpa. Express your answer in four decimal places.
AW18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P = 29 kips, w = 2.4 kips/ft, LAB = 5.6 ft, LBc = 5.6 ft, and LCD = 15.6 ft. Determine the magnitude of the maximum bending stress in the beam. P A B D LAB LBC LCD
A 62.6-kN vertical load P is applied at the corner of the square cross section of the steel compression member AB, which is free at its top A and fixed at its base B. Knowing that for the grade of steel used oy=345 MPa and E= 200 GPa, and using the allowable-stress method, determine the smallest allowable dimension d. B D 1.5 m The smallest allowable dimension dis mm.
1-45 The pedestal has a triangular cross section as shown. If it is subjected to a compressive force of 500 lb, specify the x and y coordinates for the location of point P(x, y), where the load must be applied on the cross section, so that the average normal stress is uniform. Compute the stress and sketch its distribution acting on the cross section at a loca- tion removed from the point of load application. 500 lb 3 in. 12 in. 6 in. P(x,y)
A cantilever beam of length L = 6 ft supports a uniform load of intensity q = 200 lb/ft and a concentrated load P = 2500 lb. Calculate the required section modulus if the allowable stress is 15000 psi. Select a suitable wide flange beam from the table. W8X35 W8X28 W8X21 W8X15 Weight per foot lb 35 28 21 15 Area Depth 2 In² 10.3 8.25 6.16 4.44 in 8.12 8.06 8.28 8.11 in 0.310 0.285 0.250 0.245 9= 200 lb/ft Flange Web Thickness Width Thickness In 8.020 6.535 5.270 4.015 L=6 f in 0.495 0.465 0.40 0.315 P = 2500 lb I in4 127 98 75.3 48 I S in³ 31.2 24.3 18.2 11.8
Consider the two sections with their indicated properties below to answer the following: 8-36 Ø 1000 mm Section 1 f'c fy stirrups CC 32 415 10 50 800 mm 700 mm 400 mm Section 2 f'c fy stirrups CC 600 mm rebar 21 415 10 40 32 100 mm Calculate the depth of the neutral axis of section 1 in mm. Calculate the depth of compression block of section 1 in mm. Calculate the reinforcement stress of section 1 in MPa.
3. Calculate the design moment strength øM „ for a rectangular reinforced concrete cross section having a width b of 325 mm and an effective depth d of 600 mm. The tension reinforcing steel is 4- D25 bars. f. = 27.6 MPa and f, = 276 MPa . %3D
Problem 5.23 With f, = 60,000 psi and f = 4000 psi, select the reinforcing for T beam AB for the floor system shown. Assume simple supports at A and B. The live load is to be 100 psf, while the dead load in addition to the concrete's weight is to be 80 psf. Concrete is assumed to weigh 150 lb/ft. The slab is 4 in. thick, d is 24 in., and b, is 16 in. (Ans. 3.84 in.², use 4 #9 bars) edge L. beam 5 ft 1 B T beams -4 @ 10 ft=40 ft- 5 ft 30 ft
The beam shown here is made of wood with an allowable shear stress of τall = 1100 psi. If PB = 5 kips, determine the maximum allowable force PC that can be applied on the structure before the beam fails in shear.[LAB= 2 ft, LBC= 2 ft, LCD= 1.5 ft, b = 1.25 in., h = 7 in.] Determine the maximum value of the first moment of area (Q) for the beam. (in^3) Determine the maximum allowable force at C (PC) that can be applied on the structure before it fails in shear. (kips)
A simply supported wood beam of length L = 8 ft carries a concentrated load P at midspan, as shown. The cross- sectional dimensions of the beam are b = 7 in. and h = 13 in. If the allowable shear strength of the wood is 130 psi, determine the maximum load P that may be applied at midspan. Neglect the effects of the beam's self-weight. 12 Answer: P = IM P B 7/2 C X lb N b h
A double tee cross section is used for the beam shown below. Assume the following lengths and loads: a = 15 ft b = 8 ft C= 10 ft P= 12500 Ib Q= 5000 lb The moment of inertia of the cross section is i, = 110 in.". Determine the magnitude (ie, the absolute value) of the maximum compressive bending stress in the beam. TT 3.2 in. B D 5,8 in. Answer: Omax (Compression) = 1 psi %3D
Determine the shear stress in plane AB of the beam section shown if it is subjected to a shear force V. Assume that the neutral axis passes through the A-B axis. Usar los siguientes datos: H1 = 15 in. H2 = 20 in. H3 = 8 in. W = 22 in. H2 H3 V = 300 Kips H1