What is the total elongation of steel bar having a diameter of 2 in. hanging over with a length of 10 feet? Weight of the steel is 487 lb/ ft3 and the load applied at the bottom of the shaft is 2000 lb. E = 29 x 106 psi. A)0.00240 in B)0.00279 in C)0.00289 in D)0.00250 in

What is the total elongation of steel bar having a diameter of 2 in. hanging over with a length of 10 feet? Weight of the steel is 487 lb/ ft3 and the load applied at the bottom of the shaft is 2000 lb. E = 29 x 106 psi. A)0.00240 in B)0.00279 in C)0.00289 in D)0.00250 in

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

#1 will upvote anyone who will answer correctly. Correct decimal places please. Thanks.
Fill in the blanks: The steel rod is stress-free before the axial loads P₁ =169 kN and P2 = 88 kN are applied to the rod. Assuming that the walls are rigid, calculate the axial force in each segment after the loads are applied. Use E-200 GPa. A = 2000 mm² A = 900 mm² A = 1200 mm² P P₂ B C D +250 -350 mm 500 mm A -250 mm- ANSWER: KN, PBC = PCD = KN KN, PAB = (express it in whole number)
help me pls asap D:
A hollow shaft made of red-brass copper (G = 37 GPa, shear yield strength = 150 MPa) is sandwiched between two solid shafts made of the same material. End A is fixed to a rigid wall and torques are applied to the shaft as shown. 75 kNm d₂160 kNm A d₁ L₁ B Use the following values in your working out: L₂ L₁ = 1.5 m L3 = 2.2 m d₁ = 1 m d₂ = 0.7 m d3 = 1.2 m C d₂ 3 L3 130 kNm D a) Draw a torque diagram for the entire shaft. b) Determine the maximum allowable inner diameter for the hollow section of the shaft, to the nearest mm. c) Determine the maximum length of L₂ (to the nearest mm) that will ensure the angle of twist of D relative to the wall is less than 2°. Use your value from part b for the inner diameter of the hollow shaft. d) By estimating relevant load(s), dimensions, and material properties, calculate the approximate angle of twist between two (non-coincident) points on the object shown below. Clearly state all assumptions, including the location of the chosen points.
A steel bar AD has a cross-secțional area of 260 mm? and is loaded by forçes P, = 12 kN, P2-8 kN. and P3 = 6, kN. The lengths of the segments of the bar are a = 1:5 m, b = 0.6 m, ạnd c = 0.9 m. (a) Assuming that the modulus of elasticity E = 210 GPa, calcuļate the change in length & of the bar. Does the bar elongate or shorten? (b) By what amount P should the load P, be increased so that end D of the bar does not move when the loads are applied? %3D P1 P2 P3 A в a b
Two cylindrical rods, one of steel and the other of brass, are joined at C and restrained by rigid supports at A and E. For the loading shown and knowing that E, = 200 GPa and Eb = 105 GPa, determine the deflection of point C. Sc A um →>> Dimensions in mm 120 180130- Steel B 65 KN 40-mm diam. D Brass 120 E 50 KN 30-mm diam.
The lower ends of the three bars shown are at the same level before the uniform rigid block weighing 38 kips is attached. Each steel bar has a length of 2 ft, and area of 1.9 in.?, and E = 30 x 106 psi. For the bronze bar, the area is 1.4 in.2 and E = 13 x 106 psi. Determine the length (in feet) of the bronze bar so that the load on each steel bar is twice the load on the bronze bar. Bronze Steel Steel W 2 ft 2 ft
In the figure shown, assume that a 21.3-mm-diameter rivet joins the plates that are each 118 mm wide. The allowable stresses are 119 MPafor bearing in the plate material and 54 MPa for shearing of the rivet. Determine the minimum thickness of each plate. (Answer must be in millimeters) Round your answer to 2 decimal places.
Consider the frame in (Figure 1). The crate weighs 550 lb. Follow the sign convention. Figure 4 ft O] Al B 1.5 ft 1.5 ft 1.5 ft 1.5 ft . F 6) C . E D 1 of 1 0.4 ft Determine the normal force at point F. Express your answer in pounds to three significant figures. Np = Submit ▼ Part B VE ΑΣΦ Vp = Request Answer Determine the shear force at point F. Express your answer in pounds to three significant figures. vec IVE| ΑΣΦ | | vec 1 当 ? ? lb lb
Determine the magnitude of the pin force at A. Assume W = 795 lb, a = 3.9 ft, b = 2.8 ft, r = 7 in. r W C Answer: A = i a B A D lb b
There is a journal bearing at A and a thrust bearing at B. The allowable bending stress is oallow = 14 ksi . 900 lb B 300 lb A 12 in. 24 in. 18 in. Part A Determine the smallest diameter of the shaft. Express your answer to three significant figures and include appropriate units.
А L B 425 mm C 1,000 mm V P A steel bar (1) and an Aluminum bar (2) are connected to a rigid angle ACD. Assuming: • Steel [E = 200 GPa] bar (1) is 6mm x 40mm x 600mm long. • Aluminum [E = 70 GPa] bar (2) is 10mm x 40mm x 600mm long. Poisson's ratio, v = 0.35 • A distance L of 500mm. a)Determine the force P (in kN) required to stretch the Aluminum bar by 1mm. Enter the force, P, into the d21 answer box (in kN, 3 sig digs). b) Determine the final width and thickness of the Aluminum bar. (1) Your Answer: