Problem # 2: The compound shaft made from the same material consisting of two segments AC and CB is firmly attached to rigid supports. The allowable shear stress in the shaft is limited to 5500 psi. Determine the maximum torque To that may be applied at C. Calculate also the angular rotation incurred by segment BC. Use G= 12 x 106 psi. F 0.60 in. 5.0 in. To 1.30 in. 14.5 in B

Problem # 2: The compound shaft made from the same material consisting of two segments AC and CB is firmly attached to rigid supports. The allowable shear stress in the shaft is limited to 5500 psi. Determine the maximum torque To that may be applied at C. Calculate also the angular rotation incurred by segment BC. Use G= 12 x 106 psi. F 0.60 in. 5.0 in. To 1.30 in. 14.5 in B

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An steel shaft consists of a hollow shaft 3m long, with an outside diameter of 200mm and an inside diameter of 150mm, rigidly attached to a solid shaft 2m long with a diameter of 150mm. Determine the maximum torque which can be applied without exceeding a shearing stress of 70MPa or a twist of 4.3° in the 5m length. Use G = 83GPa. 200mm 150mm 6 6 3m 2m
The double-collar bearing is subjected to an axial force P = 4 kN. Assuming that collar A supports 0.75P and collar B supports 0.25P, both with a uniform distribution of pressure, determine the maximum frictional moment M thatmay be resisted by the bearing. Take μs = 0.2 for both collars.
Answer asap
To (a) Find the forsional stiffness of the chanel section Shown, Polov (STIDEES ridots WON (6) consider a structure for which +₁ = 3/4 inch, t₁ = 1/2 inch, 6=4 inches, a = 6 inches and G = 3X107 psi. Determine the angle of twist per unit length when the structure is subjected to a torave of 25,000 1b-ins. C) If the total length of the structure of Part (b) is 6ft, and the shaft is fixes at one end, determine the maximum angle of twist. What is the angle of twist at half-span?
Don't use chat gpt It Chatgpt means downvote please solve correctly
Problem 2 The lap joint is fastened with four 3/4" diameter rivets. The working stresses are 14 ksi for the rivets in shear and 18 ksi for the plates in bearing. Find the maximum safe axial load P that can be applied to the joint. Assume that the load is equally distributed among the rivets. ANS: P = 47.3 kips P P 7 in. 8 4 in. 7 81 in. P
12. The bell crank, which is in equilibrium under the forces P and F = 36 kN inclined at θ= 48o, is supported by a pin at D. Determine the shear stress (in MPa) in the pin if it is 21-mm-diameter. P is not equal to F. Round off to two decimal places.
The pole is supported by a pin at B and A-36 steel guy wire AC. If the wire has a diameter of 0.2. Modulus of Elasticity of Steel = 200GPA or 29x103 ksi Poisson's ratio of steel=0.321 3 ft 30 D 2.5 kip 4 ft B 1. At what angle is the principal stresses on pole BC? Use Mohr's Circle. 2. What is the principal stress in pol BC? Use Mohr's Circle 3. Draw the stresses on a unit element acting on 35-degree clockwise direction of pole BC. Use Mohr's Circle. 4. What are the principal stresses in point D? Use Mohr's Circle. (answer in ksi) 5. At what angle is the principal stresses acting on point D? Use Mohr 's Circle. 6. Draw the stresses on a unit element acting on 35degree-clockwise direction of point D. Use Mohr's Circle. (answer in ksi)
T4
WHICH OF THE FOLLOWING GIVES SHERARING STRESS IF a=3inches Which of the following gives the minimum permissible dimension if the shearing stress is limited to 6000 psi