A0.475 in. diameter solid steel shaft supports two pulleys. The shaft has a length of L = 11.7 in., and the load applied to each pulley is P = 57 lb. The bearing at A can be idealized as a pin support and the bearing at D can be idealized as a roller support. Determine the magnitude of the maximum horizontal shear stress in the shaft.

A0.475 in. diameter solid steel shaft supports two pulleys. The shaft has a length of L = 11.7 in., and the load applied to each pulley is P = 57 lb. The bearing at A can be idealized as a pin support and the bearing at D can be idealized as a roller support. Determine the magnitude of the maximum horizontal shear stress in the shaft.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The circular steel shaft is subjected to two torques as shown. The segment AB is hollow, with outside diameter of 1 inch and an inside diameter of ½ inch. The segment BC is solid, with a diameter of 1 inch. Determine (a) the maximum shear stress in the shaft, and (b) the angle of twist in degrees between A and C, using G = 12 x 10⁰ psi. 750-in. Ⓡ 2 ft 2000-in. 18 Itin. 3 ft Lin.
A hollow steel [G = 12,000 ksi] shaft with an outside diameter of 3.50 in. will be subjected to a pure torque of T = 4420 lb-ft. Determine the maximum inside diameter d that can be used if the shear stress must not exceed 8,000 psi and the angle of twist must not exceed 3° in an 8-ft length of shaft. O 3.07 in. O 2.38 in. O 2.75 in. O 2.52 in. O 1.50 in.
A simple torsion-bar spring is shown. The shear stress in the steel [G= 11,500 ksi] shaft is not to exceed 8800 psi, and the vertical deflection of joint D is not to exceed 0.400 in. when a load of P = 3000 lb is applied. Neglect the bending of the shaft and assume that the bearing at C allows the shaft to rotate freely. Determine the minimum diameter required for the shaft. Use dimensions of a = 70 in., b = 24 in., and c = 24 in. a b Answer: d= D P B in. C
The 600mm diameter steel shaft is subjected to the torques shown. Determine torsion at each section. Assume G = 75 GPa. P=74 1.5P= 1.5(74) = 111 kNm 3P= 3(74)= 222kNm
If the allowable bearing stress for the material under the supports at A and B is Ob = 780 psi, determine the maximum load Pmax that can be applied to the beam. The bearing plates each have square cross sections of 5 in. by 5 in. The reactions at the supports are vertical. Assume w = 600 lb/ft, a = 12 ft, and b = 6 ft. Answer: Pmax= i W a B b lb P
1. We have a truss structure with a hinge on the left and a roller on the right. (Use method of moments ONLY for finding the members and use the numbered name only for each member) 30.00" a) Find the force acting on members 2, 3, 7, 9, 14, 15. (Indicate Compression or Tension) b) Determine the normal stress @ members 2, 3, 7, 9. (Use figure 2 for cross-sectional area) P/2 30.00" T IP 30.00" T Figure 1 30.00" P/2 30.00" P/2 10.00" 20.00" 2.00" 0.20" Figure 2 0.20" 2.00" 0.20"!
1. We have a truss structure with a hinge on the left and a roller on the right. (Use method of moments ONLY for finding the members and use the numbered name only for each member) 30.00" a) Find the force acting on members 2, 3, 7, 9, 14, 15. (Indicate Compression or Tension) b) Determine the normal stress @ members 2, 3, 7, 9. (Use figure 2 for cross-sectional area) P/2 30.00" D foo 30.00" Figure 1 30.00" (10 N -30.00" P/2 P/2 10.00" 20.00" 2.00" 0.20" Figure 2 0.20" 2.00" 0.20"
NEED IN 1 HOUR PLEASE THANK U A hollow steel shaft 10 ft long must transmit a torque of 250,000 lb-in. The total angle of twist in this length is not to exceed 2.5 degrees and the allowable shearing stress is 12,000 lb/sq.in. Determine the inside and outside diameters of the shaft if G = 12 x 106 lb/sq.in. The action is elastic.
The bell-crank mechanism is in equilibrium for an applied load of P= 48 kN. Assume that a = 230 mm, b = 180 mm, and 8 = 65°. The pin at B has a diameter of d = 30 mm, and the bell crank has a thickness of t= 10 mm. Calculate the bearing stress in the bell crank at pin B. (1) P Answer: O= i Bell crank A a C MPa B Support bracket b B F₁
A simple torsion-bar spring is shown. The shear stress in the steel [G = 11,500 ksi] shaft is not to exceed 11800 psi, and the vertical deflection of joint D is not to exceed 0.600 in. when a load of P = 2900 lb is applied. Neglect the bending of the shaft and assume that the bearing at C allows the shaft to rotate freely. Determine the minimum diameter required for the shaft. Use dimensions of a = 92 in., b = 40 in., and c = 34 in.
A simple torsion-bar spring is shown. The shear stress in the steel [G = 11,500 ksi] shaft is not to exceed 9600 psi, and the vertical deflection of joint D is not to exceed 0.650 in. when a load of P = 2800 lb is applied. Neglect the bending of the shaft and assume that the bearing at C allows the shaft to rotate freely. Determine the minimum diameter required for the shaft. Use dimensions of a = 62 in., b = 22 in., and c = 24 in.
The bell-crank mechanism is in equilibrium for an applied load of P = 34 kN. Assume that a = 240 mm, b = 140 mm, and 0 = 63°. The pin at B has a diameter of d = 15 mm, and the bell crank has a thickness of t = 6 mm. Calculate the bearing stress in the bell crank at pin B. F₁ Bell crank B a Support bracket Part 1 Use equilibrium to determine the magnitude of the reaction force at pin B. Answer: B = i kN