Problem 2: Inputs: ● ● w = 300 N/m P = 600 N a = b = 3 m c = 8 m The frame is comprised of two members. All joints are pinned. Compute the reactions at pins A and C, as well as the forces at pin B. P a) Ax (Indicate left/right) b) Ay (Indicate up/down) c) Cx (Indicate left/right) d) Cy (Indicate up/down) e) Bx (no need to indicate direction since this is an internal force) f) By (no need to indicate direction since this is an internal force) A a B b W C

Problem 2: Inputs: ● ● w = 300 N/m P = 600 N a = b = 3 m c = 8 m The frame is comprised of two members. All joints are pinned. Compute the reactions at pins A and C, as well as the forces at pin B. P a) Ax (Indicate left/right) b) Ay (Indicate up/down) c) Cx (Indicate left/right) d) Cy (Indicate up/down) e) Bx (no need to indicate direction since this is an internal force) f) By (no need to indicate direction since this is an internal force) A a B b W C

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

4 kN 4 kN 3 kN 2 kN B C D 3 m H 2'm - 5 m- -5 m- -5 m- - 5 m- Q4- The figure shows a truss that is supported at A by a pin and a roller at E. The truss is subjected to vertical forces. Determine the following: (a) check for zero-force members and identify such members (b) The Force Reactions at the supports are: Ax kN Ay kN Ey k N (c) The internal Force in member CD, FcD i . kN, specify (T) or (C) (d) The internal Force in member CF, FCF İS. . kN, specify (T) or (C) (e) The internal Force in member CD, FcG is . kN, specify (T) or (C)
The members of the truss are assumed to be pinconnected. If member CB is an A-36 steel rod of 40 mmdiameter, determine the maximum load P that can besupported by the truss without causing the member tobuckle. For A36 steel E=200 GPa and σY = 250 Mpa
From the given truss shown, FA = 150, FB = 200, and FC = 250 N. Compute the following. Specify whether the forces in each member are in tension or compression. a. find the reaction at C b. find the force in member AC c. find the force in member CD d. find the force in member AD
determine member DC
Link-2, shown in the figure, is 30 mm wide, has 12 mm diameter bearings atthe ends, and is cut from low carbon steel bar having a minimum yield strength of190 MPa. The end-condition constants for link-2 are C = 1 and C = 1.2 for bucklingin and out of the drawing, respectively.a) Draw necessary and clear free-body diagrams to determine the reactions atthe supports and the load on both member-2 and member-3. b) Determine a suitable thickness for link-2, based on a design factor of safetyηD = 4, and considering a material having E = 207 GPa, and a minimum yieldstrength Sy = 350 MPa. c) Determine the stress and resulting factor of safety for each pin, and state yoursuggestions in case of design factors less than 4. Use appropriate (SI) units as it applies (if any.)
Consider the truss shown in Picture. (a) Identify all the zero-force members. (b) Determine the force in members ML, EP, and EF. M K 2 m N, P 2 m A B CD E FG Н 2 kN 2 kN 3 KN 5 kN 16 m, 8 @ 2 m
Determine the forces in the required member of the truss, and state if the members are in tension or compression. All angles are 30, 60 and 90 degrees.What is the reaction at A? THe vertical component at Support F? Horizontal Component at Support F? Force in member BI Force in member Cl Force in member Hl
In the figure as shown below, determine the following maximum moment. a.) Reaction at A and B. P=(20+3B+C) (KN) w=(10+2D+E) (kN/m) 2+D+E(m) 2+D+E(m) B
plz help me with this one Using the Force Method , determine the reactions and the force in each member of the truss show below.
Problem 2: Determine the force in ALL the members of the truss. State if the members are in tension or compression. Show all your work to receive full credit. (Hint: It is not needed to find the reaction forces at C and E if you use the Method of Joints). Note: P1= 1000 lb and P: = 500 lb B C30 45 999 4 ft E 550 D. -4 ft- - 4 ft- 999 299
The truss in the figure is loaded by four external forces as shown below. Knowing that P1= 3 kN, P2-4 kN, P3-6 kN and P4=2 kN, a= 3 m and h=2 m, you are required to: h P1 P2 a H B members GH, BG, BC. I P3 G C P4 F D a --- a -- a a) Determine the reactions at the supports A and E. b) Using the method of joints, determine the forces of the members at joint A. c) Using the method of joints, determine the forces of the members at joint E. d) Using the method of sections, determine forces on members GF GC, CD. e) Using the method of sections, determine forces on P1 Note: You are required to draw the FBD and apply the equilibrium equations for each case. E
PLEASE SOLVE THIS AS SOON AS POSSIBLE HEHE..THANK YOU (STEP BY STEP SOLUTION) SURELY I WILL RATE YOU