Problem 2: a. What is the minimum amount of reinforcement needed in the cantilevered triangular beam below for it to be considered tension controlled? Report the required reinforcement in terms of no. 7 bars. f = 6 ksi and fy = 60 ksi b. Based on the rebar layout determined in (a), what is the maximum possible length of the beam (in feet) supporting only its self-weight? 22" L

Problem 2: a. What is the minimum amount of reinforcement needed in the cantilevered triangular beam below for it to be considered tension controlled? Report the required reinforcement in terms of no. 7 bars. f = 6 ksi and fy = 60 ksi b. Based on the rebar layout determined in (a), what is the maximum possible length of the beam (in feet) supporting only its self-weight? 22" L

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

3. A doubly reinforced beam, which have a base of 310 mm, and an effective depth of 410 mm, is reinforced with steel area of 2163 sq. mm at the bottom, and 1232 sq. mm on the top. Take d': 70 mm, fc' = 21 MPa, and fy = 345 MPa. a) What is the value of "a"? %3! %3D 89.792 mm None of the Choices 92.986 mm 86.707 mm 96.288 mm 99.699 mm
Top tie 4. Assume that the wet concrete (s.w. = 150 Ibf/ft3) behaves as a liquid. Determine the force per unit foot of length exerted on the forms. If the forms are held in place as shown, with the ties between vertical braces spaced every 2 ft, what force is exerted on the bottom tie? Brace Form 9 ft Concrete Bottom tie
SITUATION B: The beam is to carry an Ultimate Moment of 580 kN-m, geometrical property of the beam are the following: width of the beam = 350 mm, total height of %3D the beam = 670 mm , steel cover = 50mm. Use concrete strength f'c=21 MPa, steel %3D yield strength fy = 415 MPa and Ø = 0.877 %3D 4. What is the minimum number of 28-mm diameter reinforcing bars needed in the tension zone?
I need a solution quickly, Use ACI Code
When we design doubly reinforced beams, what is the maximum possible value for Ku to get minimum area of compressive steel area? Select one: a. 0.36 b. 0.4 OC. 0.545 Od. 0.6 e. 0.8 A rectangular beam section has d = 450 mm, dsc = 45 mm and Concrete grade 40 MPa. When neutral axis depth is at its limiting depth, Ast = 3600 mm^2 and Asc = 620 mm^2 were provided to satisfy the design requirement. What is the design Moment capacity (M*) of the section? Select one: a. 692.6 kNm Ob. 584.0 kNm Oc. 466.6 kNm Od. 705.1 kNm Oe. Can not estimate without the value of 'b'
Beam section is b = 300mm, h = 450 mm. %3D Steel cover is 75 mm. Compressive strength of concrete fc' = 20.7 MPa, steel strength fy = 415 MPa. The beam is simply supported on a span of 5m and carries the following loads: dead load = 13 KN/m, live load = 10 KN/m. Find the required %3D number of 20mm Ø bars for the given cross section both in balance and ultimate condition.
4.15 Determine the required area of reinforcement and the corresponding reinforcement ratio for the sections in Fig P4.1c if the ultimate moment is a) 10,000 in-kip, b) 5,000 in-kip. The reinforcement yield strength is 60,000 psi. B₁ = 0.75 £:= 6000psi = 60000psi b = 28in h = 36in Y₁ = 2.5in d:= h - y₂ = 33.5-in +AAAA- = 0.90 bw = 8 in hf := 8in B1 = 0.75 -28" 8™ 8"
3- Calculate the moment carrying capacity of the beam shown? Choose the required steel reinforcement to carry this moment. d=470mm by= 270mm and d'=30mm. C20: Allowable stress=7MPA S420: Allowable stress=220 MPa A, n=15
Design the T beam for the floor system when subjected to an ultimate moment of 300 kN-m. Beam span is 6m, beam width is 300 and d is 450mm. fc = 30 MPa, fy = 420 MPa. Determine the effective width of the T-beam in mm. Is the compressive flange adequate enough to provide the design capacity required? How many layers/rows of steel rebars are expected in the design of reinforcement? How many 25mm steel bars are required for the section?
Given are the following: 300 Unit weight of concrete = 24 kN/m3 f'c = 28 Mpa fpe = 850 MPa fpu = 1350 MPa Aps = 750 mm? foy = 1280 MPa Beam is a simple span and have a length of 24m. Use bonded tendons as prestressed reinforcement. A. Determine the value of fps (MPa) B. Determine the nominal moment strength (kN-m) 750 850
I want to solve question 1040 and the question information from question number 1039
A rectangular reinforced concrete beam exposed to earth has a total depth of 600 mm and a width o 350 mm. It is reinforced with 3-22 mm diameter bar (fy' = 315 MPa) in compression and 5 - 25 mm diameter bar in tension (fy= 345 MPа). fc' 3D 28 MPа a. determine the effective depth of the beam b. determine the depth of compression block C. check if steel yields for both tension and compression reinforcement d. determine the ultimate capacity of the beam %3D