Problem 2: A rope attached one end to a boat is wrapped around a pole to secure it for docking. If the tension in the rope, caused by the boat, is 1500 N. Determine the least number of complete turns the rope must be wrapped around the pole in order to prevent slipping of the rope. The greatest horizontal force that a man can pull the rope is 50 N. The coefficient of static friction is 0.3.

Problem 2: A rope attached one end to a boat is wrapped around a pole to secure it for docking. If the tension in the rope, caused by the boat, is 1500 N. Determine the least number of complete turns the rope must be wrapped around the pole in order to prevent slipping of the rope. The greatest horizontal force that a man can pull the rope is 50 N. The coefficient of static friction is 0.3.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A rope ABCD is looped over two pipes as shown. Knowing that the coefficient of static friction is 0.25, determine the smallest value of the mass m in kg for which equilibrium is possible. the corresponding tension in portion BC of the rope. 25 C 50 kg
A B A C D Blocks A, B, and C have weights of 93 N, 25 N, and 15 N, respectively. The coefficient of static friction between A and B is 0.3, between B and C, 0.4, and between block C and the ground, 0.35 Determine the smallest force P that will causes impending motion. Determine the friction force between A and B Determine the friction force between B and C
Teemo is trying to move the crate weighing 15 kN by pulling on the rope at an angle 0 to the horizontal. T. 11. Find the smallest possible force that Teemo should pull to cause the crate to slide. Coefficient of static friction is 0.25. 12. Determine the angle 0. 13. Determine the horizontal frictional force acting at the bottom of the crate. 14. Determine the angle of static friction? 15. If Teemo pulls the crate at the force 5kN, will the crate move? (Prove your answer mathematically)
Problem no. 2. A wheel of carries a load of 1000kg, as shown in figure. a. Determine the horizontal force P applied at the center which is necessary to start the wheel over a 5m. block. Also find the reaction at the block. b. If the force P may be inclined at any angle with the horizontal, determine the minimum value of P to start the wheel over the block; the angle P makes with the horizontal; and the reaction at the block. 7m 5m 10m
If the vertical component of the force F applied to the ring is 10 lb, determine the magnitude F and also the horizontal component. F 300
Solve for the force P required to imprend motion in the following situation: 1. If force applied to block horizontally. 2. If force applied to block downward at 30° with the horizontal. 3. What should be the minimum force P and its angle from the horizontal is required to start motion?
The three identical bars, each weighing 10.8 lb, are connected by the two freely pinned links of negligible weight and are resting on a smooth horizontal surface. Calculate the initial acceleration a of the center of the middle bar when the 7.8-lb force is applied to the connecting link as shown. 7.8 lb Answer: a = i ft/sec2
A supporting rope is loaded with a line load q(x) = q0 between points A and B. The rope shall be stretched such that the slope of the rope at point A is zero. If l = 10 m and h = 2.3 m, determine the (a) horizontal tensile force and (b) the maximum force in the rope. q0 (kN/m) = 20.627
The hoisting arrangement for lifting a large pipe is shown in the figure SD-05Q002. The spreader is a steel tubular section with outer diameter 75 mm and inner diameter 60 mm. Its length is 2.5 m and its modulus of elasticity is 200 GPa. What is the maximum weight of pipe, in kN, that can be lifted based on the following conditions? (Assume pinned conditions at the ends of the spreader.) Use: V = 3 H = 4 Problem 7 Based upon a factor of safety of 2.0 with respect to Euler buckling of the spreader. a. 205 b. 434 c. 355 d. 217 Problem 8 Based upon the allowable stress design if Fy = 248 MPa. a. 205 b. 434 c. 355 d. 217 Problem 9 Based upon the critical stress. a. 205 b. 434 c. 355 d. 217
I need the answer as soon as possible