A pulley with diameter D = 27 in weighs 80 lb. It is mounted on the diameter d = 2-in axle. A weight of 1000 lb is to be lifted. If the coefficient of friction f = 0.1, what vertical pull force P will be needed?

A pulley with diameter D = 27 in weighs 80 lb. It is mounted on the diameter d = 2-in axle. A weight of 1000 lb is to be lifted. If the coefficient of friction f = 0.1, what vertical pull force P will be needed?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

STRENGTH OF MATERIALS UPVOTE WILL BE GIVEN. Please write the complete solutions and answer all the subquestions. a. Graph the shear and moment diagram b. Find the value and location of Maximun Shear and Maximum Moment c. Give short explanation/analysis on the shear and moment diagram. (3 sentences or more)
9 ft 13 ft 22. Inad nianram Mj at point B is 10 kips-ft, P=12 kips is 9 ft from point A; and WI = 1.5 kips/ft is distributed along the length of the beam which is 22 ft. If the 1.5kips/ft uniformly distributed load will be transformed into a singular concentrated load, what will be the magnitude of Moment taken at point A? What is the equivalent singular Resultant force of the loads shown? Determine the location of the resultant R from point A.
Three wheel loads rolls as a unit across a 12-m span. The loads are A = 15 kN: B = 25 kN, 2 m to the right of A: and C = 50 kN, 6 m to the right of B. Determine the moment at A in KN-m. • Previous Next
A B 30° Determine the maximum force P that can be applied without moving the two 93-kg crates. Coefficient of Static friction = 0.25 Determine the normal force between crate A and the surface. Determine the friction force between crate A and the surface. Determine the normal force between crate B and the surface. Determine the friction force between crate B and the surface. Determine the force developed in the cord connecting cart A and B.
Using LRFD and ASD method. If the beam is replaced by W30 x 292, determine the suitable W30 column that cansupport the beam at its both ends. Hint: Solve the reaction forces first then transmit the reactionforces to the column. L1 = 3.708 m L2 = 4.708 m
A steel pad supporting heavy machinery rests on four short, hollow, cast iron piers (see figure). The ultimate strength of the cast iron in compression is 400 MPa. The total load P that may be supported by the pad is 890 kN. Using a factor of safety 3.0 with respect to ultimate strength, determine the outer diameter of the pier (in mm) if the thickness of the cross section is 10 mm. mm
STEEL DESIGN Situation 1: Situation 3: A light crane rail sits on and is securely fastened to a W crane girder. The girder is simply supported on a span of 6 m. The crane wheel loads are as follows: V = 80 kN and H = 8 kN. Assume full transfer of lateral load to the top flange of the girder. An 8-m long steel column is pinned at the top and fixed at the bottom. The column is provided with lateral support at mid-height in the weak direction. Properties: Ix = 178.1 x 10 mm4 Girder properties: ly = 18.8 x 106 mm4 A = 8129 mm²2 Weight = 67 kg/m Sx = 1, 280 x 10³ mm3 Sy = 361 x 103 mm3 7. Determine the critical slenderness ratio. a. 38 c. 27 Allowable stresses: b. 83 d. 41 Fbx = 164 MPa Find the critical buckling load. 9270 kN Fby = 186 MPa 8. 2190 kN 2310 kN a. с. Determine the actual bending stress about the x- axis. 1. b. 4730 kN d. Compute the minimum length of the column for which the Euler's formula is valid if the proportional limit of the steel used is 320 MPa. a. 99.12 MPa С. 93.75…
A garbage truck weighs 152 kN 20 m bridge girder, as shown in Figure 3. The total weight of the truck will be disuributed 38% in the passes through a front wheel while the remaining weights will be distributed at the rear wheel. If the wheels are 4 m apart from each other, determine the maximum moment applied in the bridge girder and only consider two locations of loads: one for front and the other one for rear, from the total weight of the garbage truck. Figure 3 A garbagTe truck nasses through the bridge girder
SITUATION 1: A precast girder of length 20 m is to be lifted at two points at equal distance from both ends. The weight of the girder is 0.10787 oz/mm. And its section modulus is 900,000 mm3. The moment should be made as small as possible. 1. Determine the distance (m) of the pick-up points from each end.
2. A concrete pedestal in the shape of a cube and is 6 feet on each side. The pedestal supports a superimposed load of 150,000lbs located on the Y-Y axis as shown in the diagram. Calculate the maximum eccentricity (e) for zero tension at the base of the pedestal. Include the weight of the pedestal using a concrete unit weight of 150 pcf. P = 150,000 lbs 3'-0" Y- 3'-0" 3' - (0" 3'-(" 6'-0"
The chain binder is used to secure loads of logs, lumber, pipe, and the like. If the tension T₁ is 2.3 kN when 0 = 31°, determine the force P required on the lever and the corresponding tension T₂ for this position. Assume that the surface under A is perfectly smooth. Assume a = 90 mm, b = 590 mm. T₁ Answers: P= i T₂ = Mi a A B kN KN b bo 1000000 T2 P