Problem 2: A pressure vessel with p = 200 psi internal pressure is subjected also to a twisting moment T = 450 kips in. The vessel has an internal diameter of 20 in and a wall thickness of 0.25 in. L a) Draw a Mohr's circle for an element on the front surface, as shown, and determine the principle stresses. b) Determine whether the in-plane maximum shear stress is equal to the absolute maximum shear stress. c) Determine the tensile yield strength of a ductile material which has a factor of safety of 5 for this loading. Use the maximum shear stress theory.

Problem 2: A pressure vessel with p = 200 psi internal pressure is subjected also to a twisting moment T = 450 kips in. The vessel has an internal diameter of 20 in and a wall thickness of 0.25 in. L a) Draw a Mohr's circle for an element on the front surface, as shown, and determine the principle stresses. b) Determine whether the in-plane maximum shear stress is equal to the absolute maximum shear stress. c) Determine the tensile yield strength of a ductile material which has a factor of safety of 5 for this loading. Use the maximum shear stress theory.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Copied or wrong solution get multiple downvote for sure. 1)A cylinder with a 0.3 m inner diameter and 0.4 m outer diameter is internally pressurized to 140 MPa. Determine the maximum shear stress at the outer surface of the cylinder.
The plate has a thickness of 20 mm and the force P = 3 kN acts along the centerline of this thickness such that d = 150 mm. A) Determine the normal stress at the bottom edge of the plate Enter negative value in the case of compression and positive value in the case of tension. B)Determine the normal stress at the top edge of the plate. Enter negative value in the case of compression and positive value in the case of tension. C)Specify the location of the neutral axis measured from the bottom edge of the plate.
Q5: Draw the Mohr's Circle of the stress element shown in figure. Find: - The stresses acting on inclined plane A-B with Y -axis. A 60 6 MPa B 6 MPa 6 MPa
The state of plane stress at a point on the surface of the airplane fuselage is represented by the stress element shown in the figure. Using Mohr's Circle, determine a) the principal stresses and the maximum in-plane shear stress specifying the orientation of the element in each case. b) The equivalent state of stress at the point on the element that is oriented {a} clockwise from this position Draw all the corresponding stress elements. Given x = {x} MPa; y = {y} MPa and xy = {xy} MPa xy MPa y y MPa 10000 x MPa →→→→x Solve in terms of variables
Problem 2.3 A machine bracket is loaded with an inclined force of 1000 N as shown in the figure 1000N 200mm -A- CHAPTER 250mm 1000N A 450 50mm a) Find the principal stresses at point A. b) Show the results on a properly oriented element.
): The cylinder for a hydraulic press has an inside diameter of 300 mm and an outside radius of 260 mm. Find the maximum shear stress in the cylinder for an internal pressure of (60 +120) MPa.
Q2. Show that = Cr2(a - 0 + sin 0 cos 0 – tan a cos? 0) is a permissible Airy function for the tapered cantilever of uniform thickness, shown in Figure 2, and derive expressions for the corresponding stresses or, 0g and tre. Also, find the %3D value of the radial stress at 0-0° when a=30°. w/ unit length Figure 2
3. Listed below is a combination of stresses acting at a point and referred to axes x and y in an elastic material. Using Mohr’s circle of stress determine the principal stresses at the point and their directions for each combination. 1}sigmax -60 n/mm2 , sigmay -36n/mm2 ,TAUxy=5n/mm2 2}}sigmax 30 n/mm2 , sigmay -50n/mm2, TAUxy= 30n/mm2
A pressure vessel of thickness 10 mm and inner radius 220 mm is subjected to an internal pressure of 5 MPa and torsional load of 150 N.m. T a) Determine the stress state at point A and show the results on a cubic volume element given below the figure. b) Determine the principal stresses and the maximum in- plane shear stress cases Mohr's circle at point A. Specify the orientation of the element in each case. A T Note: The results obtained by using transformation equations will not be graded even they are correct.
State of stress at the wall and the roof of the following circular opening bafore the excavation is (a] = |0 4. Find the induced stress components at point a. R W with respect to the given x-y coordinate systerm, and expresst them in the matrix form. b. Find the total stresses at point W, and give them in matrix form. c. Repeat (a) and (b) for the roof. d. Find the stresses oy, Ciy, and tyy at point A which is located at a radial distance twice the radius of the tunnel.
Asap
PROBLEM 3. The stress condition at one point in the tail region of the National Combat Aircraft is shown in the figure. (a) Calculate the principal stresses (b) Calculate the maximum in-plane shear stress and the average normal stress by analytical method and plotting the Mohr's circle. For each case, determine the element orientation and plot the stress state. (c) Calculate the maximum absolute shear stress at the same point. 40 MPa TAI 200 MPa 80 MPa