ness of 20 mm and the force P = 3 kN acts along the centerline of this thickness such that d = 150 mm.  A) Determine the normal stress at the bottom edge of the plate Enter negative value in the case of compressio

Q: Question 2) Forces of F1=3 kN in the z direction from point B, F2=9 kN in the z direction from point…

A:

Q: The forces as given below are applied as shown in the figure. F1=10 kN, F2=5 kN and F3=3 kN. The…

A: a)  -159.15 MPa(Compressive) , 35.80 MPa(shear stress) b) Principle stresses 7.686 MPa ,-166.836 MPa…

Q: Q1: Considering the forces acting on the bar having solid circular cross-section, and an elastic…

A:

Q: The control arm is subjected to the forces as shown in Figure 3.5 – 7. All dimensions are in mm. TA…

A:

Q: A thick-walled cylindrical pressure vessel having centroidal radius r and variable wall thickness t…

A: Understand that the maximum von Mises stresses occur at thickness t0. Consider that the ends of the…

Q: The rod has a diameter of 40 mm. It is subjected to the force system F₂ = 1300 N, F, = 600 N, F₂ =…

A: The rod diameter d =40 mm = 0.04mThe force systemFx= 1300NFy= 600NFz= 900NFindThe Normal stress act…

Q: A force Q is applied to a rectangular member with a size of 300mm x 450mm. Q is located 37.5mm left…

A: Answer: (a) The axial load at Q is 225 kN. (b) The stress induced at point C is 0.9167 MPa (Tension)…

Q: The rod has a diameter of 40 mm. It is subjected to the force system Fx=1100 N, Fy=500 N, Fz=900 N.…

A: The forces are The diameter od rod is The torque is

Q: he rod has a diameter of 40 mmmm. It is subjected to the force system Fx=1100 N, Fy=500 N, Fz=900 N.…

A: The forces are The diameter od rod is The torque is

Q: Q2 a) Define the term of the neutral axis. b) The steel rod having a diameter of 20 mm is subjected…

A: Given: Diameter, d=20 mmM=400 N-m

Q: Determine the max pressure that the piston-cylinder can withstand, P. Determine the magnitude of max…

A: GivenThe circumferential stress of the cylinder The inner radius of the cylinder The thickness of…

Q: Direct stresses of 120 N/mm2 (tension) and 90 N/mm2 (compression) are applied at a particular point…

A: Given data: The direct stresses in mutually perpendicular direction are σx=120 Nmm2 and σy=-90…

Q: Problem 1: A state of plane stress at a point on the surface of a structure consists of the…

A:

Q: a) Determine the internal forces acting at s b) Determine the stress components that ac =…

A: INA=2.6525×10-7m4 To-Find:- a) The internal forces acting at section a-ab) The stress components…

Q: εa and εb measurements were made when a force pair and P internal pressure were applied to the tank…

A: Longitudinal stress  Longitudinal stress is defined as the stress produced when a cylinder is…

Q: Problem 2: A state of plane stress at a point on the surface of a structure consists of the…

A: Givenσx=18ksiσy=24ksiτxy=15ksi

Q: The box wrench is subjected to the P = 70 lb force. (Figure 1) igure 2 in. 12 in. 0.5 in. B Section…

A: Principal Stresses: Principal stresses are the three mutually perpendicular normal stresses at a…

Q: Q1 / If the cross section of the femur can be approximated as a circular tube, determine the state…

A: The free-body diagram of the problem can be sketched as follows, Let the upward normal force at the…

Q: determine the diameter of the bar DE if the normal stress is limited to 100MN/m2. b) Determine the…

A: Given DataP1=30kN θ=30° {taken}

Q: Hertz contact theory can be used to determine the stresses due to contact between two spheres, which…

A: It is asked to find the stress by using Hertz contact theory

Q: A body is subjected to multiple applied loads. The resultant stress at point location (0, 1, 4)…

A:

Q: [I'wo forces are applied on the beam shown below. (a) Determine the normal and shear stresses point…

A: convert lb to kN 500 lb = 2.24 kN 400 lb = 1.78 kN convert inc to mm 1 in = 25.4 mm 10 in = 254 mm…

Q: Q2- Show the stress components of a point in plane stress on the square in Figures below: Orr = 27…

A:

Q: The gap between the aluminum bar AB and the magnesium bar 0.2 m 0.25 m CD is 0.4 mm when the…

A:

Q: The state of plane stress at a point on the surface of the airplane fuselage is represented by the…

A: To find-  1. The maximum principal stresses and the maximum in plane shear specifying the…

Q: Determine the state of stress at point A of the rectangular post shown loaded with concentrated…

A: Soln :- from equilibrium equation  Fx = + 15 kN  FY= - 75 KN  FZ= 0   ==>MX = 75 × 10 ^3 × 50…

Q: F2 (2 Q1) Axial displacement of point C in the system shown on the left is 0.01 cm. Find the maximum…

A: Write the given value using suitable variables. Here ΔlC signifies point C axial displacement, F2…

Q: 2. The L-shaped rod of 50-mm diameter is subjected to the two loadings at its end as shown in FIGURE…

A:

Q: Problem 1. The joint is subjected to a force of 250 lb as shown. The member has a rectangular cross…

A: Given Data: F=250 lbw=0.5 int=0.75 in   To Find:

Q: of the plane on which these maximum values occur.   **The answer is tensile stress is 0 ksi at 90…

A: Given data  Force p = 252 kips  Area = 6 × 6 in ^2 Find the stress and angle