Problem 18.1 Grain falls from a hopper onto chute CB at a rate of 240 lbm/s. It hits the chute at A with a velocity of 20 ft/s and leaves at B with a velocity of 15 ft/s at an angle of 10° with the horizontal as shown. Knowing that the combined weight of the chute (and the grain it supports) is 600 lbf and acts at G, determine the reaction of the roller support B and the components of the reaction of the pin at C. Hint: Watch those units! 3 ft 6 ft + A 7 ft G 12 ft B PARCO 10° Partial Answer: 400 lbf

Problem 18.1 Grain falls from a hopper onto chute CB at a rate of 240 lbm/s. It hits the chute at A with a velocity of 20 ft/s and leaves at B with a velocity of 15 ft/s at an angle of 10° with the horizontal as shown. Knowing that the combined weight of the chute (and the grain it supports) is 600 lbf and acts at G, determine the reaction of the roller support B and the components of the reaction of the pin at C. Hint: Watch those units! 3 ft 6 ft + A 7 ft G 12 ft B PARCO 10° Partial Answer: 400 lbf

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

ww. E L d Vo В A bullet weighing 0.08 lb is fired with a horizontal velocity of 1800 ft/s into the lower end of a slender 15-lb bar of length L = 30 in. The slender bar is attached at E to an initially unstretched spring of constant k= 40 lb/ft as shown. Knowing that h=10 in and d= 25in. and that the bar is initially at rest. Using the impulse - Momentum principle, determine: %3D (a) the angular velocity of the bar immediately after the bullet becomes embedded. (b) the impulsive reaction at C Assuming that the bullet becomes embedded in 0.001s and the stretch distance of the spring is 2 in immediately after impact of the bullet.
5.78
Problem 14.3 A shuttle is traveling as shown with a velocity of 1400 m/s when it deploys a capsule. The deployed capsule and shuttle have equal mass. The deployment is shown to the right in the figure. Determine the velocity (magnitude and direction) of the bottom portion of the shuttle. 5% 1200 125 m Ans: 10° < 0<20°; 1500 m/s< V< 2000 m/s
I need the answer as soon as possible
A launch vehicle has 6 engines operating in parallel which are fed from the same propellant tank. Initially, each engine has an equivalent exhaust velocity of 3500 m/s and consumes 400 kilograms of propellant per second. One of the engines malfunctions and consequently operates at 50% thrust and 120% propellant consumption. Calculate the equivalent exhaust velocity in m/s of all engines if treated as a single engine, including the malfunctioning engine in your calculation.
5. If a ball of weight W is dropped from a height h above the ground (datum), show that the total mechanical energy of the ball in its initial position equals the total mechanical energy of the ball just before it strikes the ground AND also equals the total mechanical energy of the ball when it has fallen h/2. h Datum h 2 Potential Energy (max) Kinetic Energy (zero) Potential Energy and Kinetic Energy Potential Energy (zero) Kinetic Energy (max)
A motorcycle and rider have a combined mass of 350kg. The vehicle's velocity is 100 km/hr. The rider is to go up a hill incline of 10 meters. The wheels each have a mass of 20 kg and a diameter of 500mm. The wheel design consists of 6 spokes with a mass of 0.5 kg for each spoke. a. Determine the vehicle's velocity at the top of the hill, assuming it was a rolling vehicle with engine being turned off. a. Indicate the vehicle's velocity at each meter through the climb. b. Explain the transfer energy and how this affects the behaviour of the system. At another point in its journey, the motorcycle and rider travel at 80 km/h around a left-hand bend of radius 30m. Calculate: a) The angular velocity of each wheel. b) The moment of inertia of each wheel. c) The angular momentum of the wheel prior to entering the bend. d) The magnitude of the gyroscopic torque produced on the bike as the rider is driving around the bend. What is the effect and why is it important to calculate the gyroscopic…
A crane lifts a 2500-kg beam with a varying lifting force F = (28000 + 3000S²) N. Determine the final velocity of the beam when it is lifted to a height of s = 3m.
A stream of water flowing at a rate of 1.2 m3/min and moving with a speed of 30 m/s at both A and B is deflected by a vane welded to a hinged plate. Knowing that the combined mass of the vane and plate is 20 kg with the mass center at point G , determine (a) the angle 0, (b) the reaction at C.
A power specification formula is to be derived for electric motors which drive conveyor belts moving solid material at different rates to different heights and distances. Denoting the efficiency of the motors by h and neglecting the power needed to drive the belt itself, derive a formula in the SI system of units for the power P in kW, in terms of the mass flow rate m in kg/h, the height b and horizontal distance I in meters. b
6. Exercise 2.5.32 Block A is observed to be dropping down at a steady 0.9 ft/s. At what velocity must the free end of the pulley be moving? L