applied mechanics 2 PROBLEM 13.50A power specification formula is to bederived for electric motors which driveconveyor belts moving solid material atdifferent rates to different heights anddistances. Denoting the efficiency of themotors by n and neglecting the powerneeded to drive the belt itself, derive abformula (a) in the SI system of units forthe power P in kW, in terms of the massflow rate m in kg/h, the height b andhorizontal distance I in meters.

PROBLEM 13.50 A power specification formula is to be derived for electric motors which drive conveyor belts moving solid material at different rates to different heights and distances. Denoting the efficiency of the motors by ŋ and neglecting the power needed to drive the belt itself, derive a formula (a) in the SI system of units for the power P in kW, in terms of the mass flow rate m in kg/h, the height b and horizontal distance / in meters.

PROBLEM 13.50 A power specification formula is to be derived for electric motors which drive conveyor belts moving solid material at different rates to different heights and distances. Denoting the efficiency of the motors by ŋ and neglecting the power needed to drive the belt itself, derive a formula (a) in the SI system of units for the power P in kW, in terms of the mass flow rate m in kg/h, the height b and horizontal distance / in meters.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Where does the absolute maximum shear stress in an element of material occur?
Develop a generalized form of Hooke's law?
An impact test was done on specimen M and R and the results are shown in Fig. Q2(c) and Table Q2(c). Based on the obtained results, choose whether specimen M or R is brittle or ductile in terms of: Impact strength Fracture surface Specimen M Specimen Impact Strength (J/m²) Fig. Q2(c) Table Q2(c) M 4.35 x 105 Specimen R R 1.21 x 106
Which of the following occurs when the value of Poisson’s ratio is doubled and the modulus of elasticity is kept constant? a. The lateral deformations experienced by the material is halved b. The volume of the material will remain constant when subjected to external forces c. The elastic region of the shear stress-strain diagram would be less steep d. The material can withstand higher amounts of stress before permanent deformations occur
. A stress-strain diagram for a polymer is shown. Identify items A, B, and C. A A= lower yield point; B = proportional limit; C = upper yield point A= yield point; B= elongation at fracture; C = fracture point none of the choices A= lower yield point; B = plastic deformation; C = upper yield point A= yield point; B = elastic deformation; C = elastic limit а. d. b. е. с.
1,000,000 mm = ? m 2. 1,000,000 µg = ?g 3. 1,000,000 mg =?g 4. 1,000,000 cm =? m 5. 1,000,000 mL = ?L 6. 1,000,000 um = ? cm 7. 1,000,000 mm = ? km 8. 1,000,000 cm = ? km 9. 1,000,000 mg = ? kg 10. .1,000,000 g = ? mg 11. 1,000,000 km = ? m 12. 1,000,000 kg =2g 1. 13. 1,000,000 km = ? cm 14. 1,000,000 mL = ? L 15. 1,000,000 kg =? mg 16. 1,000,000 cg =?g 17. 50 mi = ? in PART A-3 18. 42 °F = ? °C 19. 73 °F = ?° C 20. 12 °C = ? °F 21. 70 °C = ? °F 22. 25 °C = ? K 23. 300 °K = ? °C 24. 100 ft/sec =? mi/hr 25. 100 mi / hr = ? ft / sec. 26..5 gal / min = ? gal/hr 27. 5 pints / min = ? gal / hr 28. 3 g/cm3 = ? kg/m3 29. 180 kg / m3 =? g/ mm3 30. 200 lb/in2 = ? tons/ft2 31. 2.5 tons / ft2 = ? lb / in2 32. 100 km/hr = ? m/sec 33. 250 m/min =? km / hr 34. 100 m/sec = ? km/hr 35. 250 km / hr = ?m/ min 36. 2 cc/sec = ? L/hr 37. 2L/ hr = ? c / min 38. 2 m3 = ?L 39. 18 L = ? m3 n Tahminleri: Acık
What is the origin of elasticity in material
4. For a brass alloy, the stress at which plastic deformation begins is 345 MPa and the modulus of elasticity is 103 GPa. What is the maximum load that may be applied to a specimen with a cross-sectional area of 130 mm² without plastic deformation? b. If the original specimen length is 76 mm, what is the maximum length to which it may be stretched without causing plastic deformation?
What is thermal gradient in thermal stress [explained thoroughly]
Question 1 You are working on a design team at a small orthopaedic firm. You have been asked to select a cobalt- chrome-molybdenum (CoCr) material that will not experience plastic deformation under a specific mechanical test, as follows... A tensile stress is applied along the long axis of a solid cylindrical rod that has a diameter of 10 mm. An applied load of some magnitude F produces a 7x10³ mm change in diameter (see figure below, original shape is blue, elongated shape is unshaded). Q1H: Provide a brief rationale based on calculations used to support your answer. That is, how would you explain the behavior of the "new alloy" material to your design team? Table of properties: Assume Poisson's ratio is 0.3 for all materials Process Elastic Modulus (GPa) Material CoCr F75 As cast/Annealed 210 CoCr F90 Hot forged New alloy Z X ↑ F df O 210 110 Yield Strength (MPa) 450-517 900-1200 600 Tensile Strength (MPa) 655-890 1400-1600 700
Area A1 in Figure 1.3 represents the material's properties of: (a) Ductility. (b) Modulus of Elasticity. (c) Modulus of Resilience. (d) Modulus of Toughness. A1
1-Explain why flexural strength of brittle materials is always higher than tensile strength of the same material?