Problem (11) A 60-mm radius drum is rigidly attached to a 100-mm radius drum as shown. One of the 100 mm 60 mm drums rolls without sliding on the surface shown, and a cord is wound around the other drum. Knowing that end E of the cord is pulled to the left with a velocity of 120 mm/s, determine A E a) the angular velocity of the drums b) the velocity of the center of the drums c) the length of cord wound or unwound per second. D

Problem (11) A 60-mm radius drum is rigidly attached to a 100-mm radius drum as shown. One of the 100 mm 60 mm drums rolls without sliding on the surface shown, and a cord is wound around the other drum. Knowing that end E of the cord is pulled to the left with a velocity of 120 mm/s, determine A E a) the angular velocity of the drums b) the velocity of the center of the drums c) the length of cord wound or unwound per second. D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 2.5-kg homogeneous disk of radius 80 mm rotates at the constant rate ω1 = 50 rad/s with respect to arm ABC, which is welded to a shaft DCE. Knowing that at the instant shown, shaft DCE has an angular velocity w2 = (12 rad/s)k and an angular acceleration a2= = (8 rad/s2)k, determine (a) the couple that must be applied to shaft DCE to produce that acceleration, (b) the corresponding dynamic reactions at D and E.
A semicircular panel with a radius r is attached with hinges to a circular plate with a radius r and initially is held in the vertical position as shown. The plate and the panel are made of the same material and have the same thickness. Knowing that the entire assembly is rotating freely with an initial angular velocity of w0 , determine the angular velocity of the assembly after the panel has been released and comes to rest against the plate.
1. A 60-mm-radius drum is rigidly attached to a 100-mm-radius drum as shown. One of the drums rolls without sliding on the surface B shown, and a cord is wound around the other drum. Knowing that end E of the cord is pulled to the left with a velocity of 120 mm/s, determine (a) the angular velocity of the drums, (b) the velocity of the center of the drums, (c) the length of cord wound or unwound per second. 100 mm 60 mm B E
17.24 The 1.5-kg uniform slender bar AB is connected to the 3-kg gear B which meshes with the stationary outer gear C. The centroidal radius of gyration of gear B is 30 mm. Knowing that the system is released from rest in the position shown, determine (a) the angular velocity of the bar as it passes through the vertical position, (b) the corresponding angular velocity of gear B. - 120 mm aff maya mam 50 mm wwww Fig. P17.24 and P17.25 B www C
Problem 6.169 At the instant shown, bar AB rotates with a constant angular velocity WAB 24 rad/s. Letting L= 0.75 m and H= 0.85 m, determine the angular acceleration of bar BC when bars AB and CD are as shown, i.e., B parallel and horizontal. WAB
A 6-lb homogeneous disk of radius 3 in. spins as shown at the constant rate w1 = 60 rad/s. The disk is supported by the fork-ended rod AB , which is welded to the vertical shaft CBD The system is at rest when a couple M0 is applied as shown to the shaft for 3 s and then removed. Knowing that the maximum angular velocity reached by the shaft is 18 rad/s, determine (a) the couple M0) the dynamic reactions at C and D after the couple has been removed.
Problem 16.137 At the instant shown in (Figure 1), rod AB has an angular velocity WAB = 3.0 rad/s and an angular acceleration AB = 10 rad/s². The collar at C is pin-connected to CD and slides over AB. Figure 60° @AB αAB 0.75 m с 0.5 m B 1 of 1 Part A WCD= Determine the angular velocity of rod CD at this instant. Express your answer in radians per second to three significant figures. Enter positive value if the direction of velocity is counterclockwise and negative value if the direction of velocity is clockwise. IVE ΑΣΦΑ ↓↑ vec Submit Part B αCD = Request Answer Submit Determine the angular acceleration of rod CD at this instant. Express your answer in radians per second squared to three significant figures. Enter positive value if the direction of acceleration is counterclockwise and negative value if the direction of acceleration is clockwise. [Π ΑΣΦ Request Answer ? vec rad/s ? < rad/s² 8 of 8 Review
Two uniform cylinders, each of weight W=14 lb and radius r = 5 in, are connected by a belt as shown. Knowing that at the instant shown the angular velocity of cylinder A is 30 rad/sec counterclockwise, determine (a) the time required for the angular velocity of cylinder A to be reduced to 5 rad/sec, (b) the tension in the portion of belt between the two cylinders. *** Solve using the method of impulse-momentum *** B
The four bar linkage in Fig. 2 is driven by link 2 at constant angular velocity of 300rpm ccw. Determine angular velocity of link 3, absolute velocity of point E and C when B=30° 25 mm A B B 110 mm. 100 mm. Fig. 2 40 mm 65 mm D E A
Only need A, B, and C please.
A triangular plate and two rectangular plates are welded to a straight bar AB. The welded unit rotates completely about the axis AB with a constant angular velocity of 7.5 rad/s and decreasing at a rate of 22.5 rad/s2. Knowing that at the instant considered the velocity of corner E is directed downward, determine the velocity and acceleration of corner C. A 400 mm D B 300 mm E 350 mm
Dynamic question