Example 7.3. In Fig. 7.9, the angular velocity of the crank OA is 600 r.p.m. Determine the linear velocity of the slider D and the angular velocity of the link BD, when the crank is inclined at an angle of 75° to the vertical. The dimensions of various links are : OA =28 mm; AB =44 mm; BC 49 mm; and BD =46 mm. The centre distance between the centres of rotation O and C is 65 mm. The path of travel of the slider is 11 mm below the fred point C. The slider moves along a horizontal path and OC is vertical.

Example 7.3. In Fig. 7.9, the angular velocity of the crank OA is 600 r.p.m. Determine the linear velocity of the slider D and the angular velocity of the link BD, when the crank is inclined at an angle of 75° to the vertical. The dimensions of various links are : OA =28 mm; AB =44 mm; BC 49 mm; and BD =46 mm. The centre distance between the centres of rotation O and C is 65 mm. The path of travel of the slider is 11 mm below the fred point C. The slider moves along a horizontal path and OC is vertical.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The system shown in the figure is composed of bar AB which is pin-supported at A and attached to bar BC. The end of bar BC is connected to the slider block C. At the instant shown, the acceleration of point B is 1.125 m/s2 downward and the angular velocity of bar BC is 0.5625 rad/s counterclockwise. What is the angular acceleration of bar AB?
160 mm -80 mm- 250 mm Figure 3: Schematic for Question 3. The 80-mm-radius wheel shown rolls to the left with a velocity of 900 mm/s. Knowing that the distance AD is 50 mm, determine the velocity of the collar and the angular velocity of rod AB when 3 = 0 and when 3 = 90 deg.
5. For the following pin-collected link assembly, link AO is pinned at point O, and moves with angular velocity W and angular acceleration a (both counterclockwise). 4) if W = 4.0 rad/s and a = 6.3 rad/s2, length I = 1.5 m, and angle 0= 36°, what is the magnitude of the angular velocity of link AB? Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point, and proper unit. 0.5 m 0, a B Your Answer: Answer units
Please answer part (a) and (b)
Two shafts the axes of which intersect but are inclined to each other at 20 degreeconnected by means of a universal joint. At what position in the rotation cycle of thedrive shaft (i) velocity ratio will be maximum, minimum and unity (ii) the accelerationis maximum?
The oscillating link OAB of a mechanism, as shown in Fig. 7.35, is pivoted at O and is moving at 90 r.p.m. anticlockwise. If OA = 150 mm; AB = 75 mm, and AC= 250 mm, calculate 5. 15° 1. the velocity of the block C; 2. the angular velocity of the link A C; 200 mm and 3. the rubbing velocities of the pins at 0, A and C, assuming that these pins are of equal diameters of 20 mm. [Ans. 1.2 m/s; 1.6 rad/s² clockwise; 21 250 mm 75 mm 200 mm/s, 782 mm/s, 160 mm/s] B 6. The dimensions of the various links of a Fig. 7.35 mechanism, as shown in Fig. 7.36, are as follows : AB = 30 mm ; BC = 80 mm ; CD = 45 mm ; and CE = 120 mm. 30° 75 mm 22.5 mm E D. Fig. 7.36
The system shown in the figure is composed of bar AB which is pin-supported at A and attached to bar BC. The end of bar BC is connected to the slider block C. At the instant shown, the acceleration of point B is 1.125 m/s2 downward and the angular velocity of bar BC is 0.5625 rad/s counterclockwise. What is the angular speed of bar AB?
Parvinbhai
2. Two rigid links are rotating in the horizontal plane as shown in the figure below. The left-most link rotates with angular rate ₁ of 4 rad/s. The end of the right-most link holds a pin which is confined to move along a slot in the other link. The length of the right-most link 72 is 0.45 m. Determine the angular rate ₂ of the second link at the instant shown. Use 0₁ = 30°, 0₂ = 60°, and r₁ = 0.6 m. 0
The double gear in the system of gears below is unrestricted in its horizontal movement. Find the double gear's angular velocity and the velocity of its center C. The velocity at D is 30 m/s to the right. Note: Start with identifying the planar motion each rigid body experiences. o = 12 ma ល rads –156 mm ប B 100 mm បំណ ម្ហូបបុ 100 mm ឬល VD
The mechanism shown is composed of rod GPV pin-connected to rod DPE at point P. Knowing that the velocity of V is 4 m/s downwards, A. Redraw bar GPV and determine its instantaneous center of rotation (label it as point C). Specify all angles and distances needed. B. Determine the angular velocity of rod GPV. C. Determine the velocity of point P. D. Redraw bar DPE and determine its instantaneous center of rotation (label it as point C). Specify all angles and distances needed. E. Determine the angular velocity of rod DPE. Use IC method. Please don't show me the answer in chegg. I think there is an error
The mechanism below has a crank that revolves clockwise at point O at a speed of 2000 rpm. Using vector diagrams, determine: a) The linear velocity of the piston and the angular velocity of the link AB about A. b) The angular acceleration of the link AB about A and the inertial resistance produced by the piston. c)Using trigonometry, confirm your results for the velocity in parts (i), explain your reasons behind which method is preferable, and identify the error margin for your velocity answers.