PROBLEM 1. The AD beam shown in the figure is supported by BC rod with pin connections. The pin at support A is in double shear, while the pins at B and C are I. in single shear. If BC rod has an allowable tensile stress of 200 MPa and the pins A, B and C have an allowable shear stress of 70 MPa, determine (a) the required diameter of the rod BC. (b) the minimum required diameter of pins A, B and C to the nearest 1 mm.

PROBLEM 1. The AD beam shown in the figure is supported by BC rod with pin connections. The pin at support A is in double shear, while the pins at B and C are I. in single shear. If BC rod has an allowable tensile stress of 200 MPa and the pins A, B and C have an allowable shear stress of 70 MPa, determine (a) the required diameter of the rod BC. (b) the minimum required diameter of pins A, B and C to the nearest 1 mm.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 50 mm diameter circular bar is used as a simply supported beam 10 m long, is simply supported at the left- hand end and at its mid- point. it carries a uniformly distributed load of 48 KN/m between the supports and a point load of 50 KN at the right- hand end. Determine : (a) draw shear force and moment diagrams. ( b) flexural * .stress
Problem 1.3-5. The truss shown carries two forces: a horizontal rightward force of 50 kN and a vertical downward force of 100 kN. A roller supports the truss at A and a pin at H. If the pin's allowable shearing stress is 150 MPa, solve the pin's minimum diameter to carry the applied load safely. (Hence: The pin at A is at a state of a double shear.) D. B. 50 kN 1 m 1 m H. 1 m G. 1 m 1 m Detail at A 100 kN
please answer quickly
Q8(): For the truss shown in the Figure, if the diameter of pins at A and G are 3 in and2 in, respectively. Both stresses in A and 70 kips 50 kips A 4ft В 4# C 4ft are double shear. Determine the shear stresses in 9 ft pins at A and G and the stresses members AG; AF member GF if their diameter is 4 in and in.
Q70: For the truss shown in the Figure, if the diameter of pins at A and E are 60mm and 80mm, respectively. The stress in A is double shear while it is single shear in E. Determine the shear 3m 2m 2m 3 m 3 m 3 m F 3 m 110KN 110 KN stresses in pins at A and E and the stresses in members BG; and member BC if their diameter is 110 mm.
Calculate the average shear stress in MPa of the pins Band C on the frame shown in the figure. Note that thesepins are subjected to double shear and have a diameterof 0.5 inch.
A homogenous bar AC with negligible mass is supported by a pin at A and cable BC, carried a load of 20 kN as shown in the figure. Determine the pin diameter at A if the allowable shearing stress is 80 MPa. (double shear) 3 m. 4 m. C 20 kN B.
2 kip/ft 6 in 10 in B. 40 kip 16 in D. 16 In 5 ft 5 ft 10 ft The simply-supported beam-column above is subjected to a uniformly distributed load and an axial load, as shown. Assume that the Internal resultants on the cross-section passing through point D are as follows: • ND -40 kip • VD 0 Mp = +100 kip-ft Which of the following is closest to the longitudinal normal stress at point D? O-78.1 psi +235 psi O-153 psi O-1.77 ksi H:
Calculate the average shear stress in MPa of the pins Band C on the frame shown in the figure. Note that thesepins are subjected to double shear and have a diameterof 0.5 inch.