A 150mm x 250 mm simply supported wood beam is reinforced with a steel plate of width attached at the bottom fiber. Determine the width b of the steel plate fastened so that the working stresses of 8.2 MPa for wood and 124 MPa for steel are reached simultaneously. Use n = 20.

A 150mm x 250 mm simply supported wood beam is reinforced with a steel plate of width attached at the bottom fiber. Determine the width b of the steel plate fastened so that the working stresses of 8.2 MPa for wood and 124 MPa for steel are reached simultaneously. Use n = 20.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.9.3P: A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the...

See similar textbooks

Similar questions

A 20 mm diameter steel rod passes concentrically through a bronze tube (200+SN) mm long, 50 mm external diameter and 40 mm internal diameter. The ends of the steel rod are threaded and provided with nuts and washers which are adjusted initially so that there is no end play at 25°C.. 1. Assuming that there is no change in the thickness of the washers, if the stress produced in the steel is (200+SN) MN/m2 when one of the nuts is tightened, the pitch of the thread being 1 mm. Find the number of turns for the nut and stress in bronze tube.2. If the temperature of the steel and bronze is then raised to 4O°C find the changes that will occur in the stresses in both materials. The coefficient of linear expansion per C is 10 x10-6 for steel and 17 x10-6 for bronze. E for steel = 210 GN/m2. E %3D for bronze = 100 GN/m2.. Note: SN = %3D Student number Student Number =32
A reinforced concrete column 400 mm in diameter is designed to carry an axial compressive load of 400 kN. Determine the required area of reinforcing steel if the allowable stresses are 6 MPa and 120 MPa for the concrete and steel, respectively. Use Econcrete = 14 GPa and Esteel = 200 GPa.
An aluminum alloy cylindrical roller with diameter 1.25 in and length 2 in rolls on the inside of a cast-iron ring having an inside radius of 6 in, which is 2 in thick. Find the maximum contact force F that can be used if the shear stress is not to exceed 4000 psi.
A steel rod of circular cross section will be used to carry an axial load of 89 kips. The maximum stresses in the rod must be limited to 36 ksi in tension and 16 ksi in shear. Determine the required diameter for the rod.
A timber column, 8in. by 8in. in cross section is reinforced on all four sides by steel plates, each plate being 8in. wide and "t"in. thick. Determine the smallest value of "t" for which the column can support an axial load of 300 kips if the working stresses are 1200psi for timber and 20ksi for steel. The moduli of elasticity are 1.5x10^6psi for timber and 29x10^6psi foe steel -Draw and label the diagram correctly, No diagram in the solution will be marked wrong. -Shortcut solution will be marked wrong.- Direction of the assumption of the equilibrium equation must be shown, no direction will be marked wrong.
The compound bar carries the axial forces P and 2P. Find the maximum allowable value of P (in lbs) if the working stresses are 40 ksi for steel and 20 ksi for aluminum, and the total elongation of the bar is not to exceed 0.2
1. A bronze bar is fastened between a steel bar and an aluminum bar as shown. Axial loads are applied at the positions indicated. Find the largest value of P that will not exceed an overall deformation of 3.0 mm, or the following stresses: 140 MPa in the steel, 120 MPa in the bronze, and 80 MPa in the aluminum. Assume that the assembly is suitably braced to prevent buckling. Use EsT=200GPA, EAL = 70 GPa, and EBr = 83 GPa. As = 480 mm? Ab=650 mm? Al= 320 mm? 2P 4P 3P 1m 2m 1.5m
2. If the allowable shear stress for each of the steel pins at A and B is tpe 6.5 ksi and the allowable normal stress for bar CB is Operm 10 ksi, determine the diameter of the pins at A and B and that of the square bar CB. Pin A is in double shear while Pin B is in single shear. Ignore points D and E. (^ } 2.5 ft -3 ft -5 ft 150 lb/ft Fx =
A cantilever beam, 80 mm wide by 260 mm high and 9 m long, carries a load that varies uniformly from zero at the free end to 1200 N/m at the wall. Determine the magnitude of the stress in a fiber 60 mm from the top of the beam at a section 4 m from the free end. Answer must be in MPa
Required information Link AB, of width b = 2 in. and thickness t= in., is used to support the end of a horizontal beam. The average normal stress in the link is -21 ksi and the average shearing stress in each of the two pins is 12 ksi. 4 NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Determine the diameter d of the pins. The diameter d of the pins is in.
The lap joint shown is fastened by 4 rivets of ¾ in. diameter. Find the maximum load P that can be applied if the working stress are 14000 psi for shear in the rivet and 18000 psi for bearing in the plate. Assume that the applied load is distributed evenly in the 4 rivets. The plate is 7/8 in. thick and 4 in wide.
For the clevis connection shown, the shear stress in the 5/16-in.-diameter bolt must be limited to 32 ksi. Determine the maximum load P that may be applied to the connection. Clevis O 3.96 kips O 4.91 kips O 5.19 kips 3.44 kips O 6.79 kips