A steel rod of circular cross section will be used to carry an axial load of 89 kips. The maximum stresses in the rod must be limited to 36 ksi in tension and 16 ksi in shear. Determine the required diameter for the rod.

A steel rod of circular cross section will be used to carry an axial load of 89 kips. The maximum stresses in the rod must be limited to 36 ksi in tension and 16 ksi in shear. Determine the required diameter for the rod.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter5: Stresses In Beams (basic Topics)

Section: Chapter Questions

Problem 5.9.4P: A circular pole is subjected to linearly varying distributed force with maximum intensity t0....

See similar textbooks

Related questions

Q: Two solid cylindrical rods support a load of P = 27 kN as shown. Rod (1) has a diameter of 17 mm,…

Q: TOP The assembly shown has pin support at E and roller support at V. A steel rod is connected at M…

Q: A rod has a solid circular cross section with a diameter of 40 mm is subjected to the shown loads.…

A: To find: The state of stress at point A. Given: The area moment of inertia of solid circular cross…

Q: A motorcycle's clutch hand lever is designed to receive a load from the rider's finger of 50 N at…

A: &#x3C3;=F&#x200B;A" data-mce-style="display: inline-block; line-height: 0; text-indent: 0px;…

Q: A lever is attached to a shaft with a square shear key as shown. The force applied to the lever is P…

A: Given:P=300 Nσ=72 MPaL=31 mm

Q: A compound bar consists of a circular rod of steel of diameter 25 mm, rigidily fitted into a copper…

Q: The drive shaft of a car is designed to be a tube with an outer diameter of 4 in. The engine…

A: Given the following data:Outer diameter of the shaft, do= 4inPower delivered by the engine, P= 190hp…

Q: A cantilever beam, 80 mm wide by 270O mm high and 8 m long, carries a load that varies uniformly…

A: Draw a diagram for the cantilever beam. Here, w1 is the load intensity at point B i.e. at 5 m from…

Q: A hollow steel tube with an inside diameter of 80 mm must carry an axial tensile load of 330 kN.…

Q: A column is fabricated by adhesively bonding two aluminum faceplates to a foam plastic core as shown…

A: σa = -83.93MPaσf = -1.35MPaδcolumn = 2.07mmExplanation:

Question

A steel rod of circular cross section will be used to carry an axial load of 89 kips. The maximum stresses in the rod must be limited to 36
ksi in tension and 16 ksi in shear. Determine the required diameter for the rod.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: To determine the diameter of the rod

VIEW

Step 2: Calculate the diameter.

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 10 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A vertical pole consisting of a circular tube of outer diameter 5 in. and inner diameter 4.5 in. is loaded by a linearly varying distributed force with maximum intensity of q0, Find the maximum shear stress in the pole.
An elevated jogging track is supported at intervals by a wood beam AB (L = 7.5 ft) that is pinned at A and supported by steel rod BC and a steel washer at B. Both the rod (dBC= 3/16 in.) and the washer (dB= 1.0 in.) were designed using a rod tension force of TBC=415 lb. The rod was sized using a factor of safely of 3 against reaching the ultimate stress tru— 60 ksi. An allowable bearing stress sba= 565 psi was used to size the washer at B. A small platform HF is suspended below a section of the elevated track to support some mechanical and electrical equipment. The equipment load is uniform load q = 50 lb/ft and concentrated load WE= 175 lb at mid-span of beam HF. The plan is to drill a hole through beam ABaX £land install the same rod (dBC) and washer) dB) at both D and F to support beam HF. (a) Use s and to check the proposed design for rod DF and washer d,: are they acceptable? (b) Re-check the normal tensile stress in rod BC and bearing stress at 8 if either is inadequate under the additional load from platform HF. Re-design them to meet the original design criteria.
Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa
Repeat the previous problem using ? = 50° and stresses on the rotated element: sy1= 70 MPa, ??y1=-82 MPa, and tx1y1=-35 MPa.
A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the figure. The diameter dBof the bar is 1/4 in., the diameter D Wof the washers is 7/8 in., and the thickness is of the fiberglass deck is 3/8 in. If the allowable shear stress in the fiberglass is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi, what is the allowable load P allowon the tie-down?
A circular post, a rectangular post, and a post of cruciform cross section are each compressed by loads that produce a resultant force P acting at the edge of the cross section (see figure). The diameter of the circular post and the depths of the rectangular and cruciform posts are the same. For what width b of the rectangular post will the maximum tensile stresses be the same in the circular and rectangular posts? Repeat part (a) for the post with cruciform cross section. Under the conditions described in parts (a) and (b), which post has the largest compressive stress?
2. If the allowable shear stress for each of the steel pins at A and B is tpe 6.5 ksi and the allowable normal stress for bar CB is Operm 10 ksi, determine the diameter of the pins at A and B and that of the square bar CB. Pin A is in double shear while Pin B is in single shear. Ignore points D and E. (^ } 2.5 ft -3 ft -5 ft 150 lb/ft Fx =
A line shaft rotating at 200 rpm is to transmit 20 kW. The allowable shear stress for the material of the shaft is 42 MPa. If the shaft carries a central load of 900 N and is simply supported between bearing 3m apart, determine the diameter of the shaft.o The maximum tensile or compressive stress is not to exceed 56 MPa.
The member consists of the steel rod AB that is screwed into the end of the bronze rod Find the largest value of P that meets the following design criteria: (a) the overall length of the member is not to change by more than 3 mm; and (b) the stresses are not to exceed 140 MPa in steel and 120 MPa in bronze. The moduli of elasticity are 200 GPa for steel and 80 GPa for bronze.
4. What length of a square key is required for a 4-in diameter shaft transmitting 1000 hp at 1000 RPM? The allowable shear and compressive stresses in the key are 15 ksi and 30 ksi, respectively.
0.75mm when carrying the load of 60KN. Find the modulus of elasticity of the material of the the width of the bar to limit the maximum stress to 150MPA. If the bar which is 1m extends by a. A metal thickness 16mm and having a rectangular cross-section carries a load of 60KN. Find bar.
Its from Solid Mechanics I