A line shaft rotating at 200 rpm is to transmit 20 kW. The allowable shear stress forthe material of the shaft is 42 MPa. If the shaft carries a central load of 900 N and issimply supported between bearing 3m apart, determine the diameter of the shaft.oThe maximum tensile or compressive stress is not to exceed 56 MPa.

Answered: Image /qna-images/answer/d7dc960b-88c5-43b6-8638-3bb723429b82.jpg

A line shaft rotating at 200 rpm is to transmit 20 kW. The allowable shear stress fo the material of the shaft is 42 MPa. If the shaft carries a central load of 900 N and simply supported between bearing 3m apart, determine the diameter of the shaf The maximum tensile or compressive stress is not to exceed 56 MPa.

A line shaft rotating at 200 rpm is to transmit 20 kW. The allowable shear stress fo the material of the shaft is 42 MPa. If the shaft carries a central load of 900 N and simply supported between bearing 3m apart, determine the diameter of the shaf The maximum tensile or compressive stress is not to exceed 56 MPa.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the uniform cross-section of the truss members BC, BE and AE, if the allowable stresses for all members is 150 psi for tension and 125 psi for compression. Given that applied force at point is P = 3.6 kips as shown. Neglect weight of truss members. Find the answer for A only. Answer: A = ___________________
Q1: determine the increase in vertical stresses at depth of Z=3.5 m under points A, B and C due to apply rectangular and ring foundations. The surface load intensity of rectangular is 250 kN/m2, while the surface load intensity of ring is 300 kN/m?.The drawing was done without scale and all dimensions in (m). R1 R2 X1 X2 B L 3 4.5 7.5 12 X1 X2 Aqs-net(2) R1 R2 Aqs-net(1) B B.
F The shaft is loaded with two forces as shown and is fixed at A. The strength is defined as the maximum allowable force F that does not produce shear stress above the material's maximum al- lowable value of 4 ksi. Determine the strength. By what factor would the strength increase if the shaft diameter were doubled? (L₁ = 12 in., L₂ = 6 in., and d = 0.5 in.)
Determine the principal stresses andmaximum in-plane shear stress of given stresselement.
QI/ For the assembly below, determine the average normal stress for the cable. Assume that the cable has a diameter of 10 mm. take P =12 kN. 0.5 m -0.75 m -0.75 m 0.75 m
determine the maximum normal stress and the maximum shear stress at point O
Two loads P act as shown, one parallel to (x0) and another parallel to z0; each load P equals 2.0 kN. The crankshaft dimensions are b1 = 90 mm, b2 = 120 mm, and b3 = 40 mm. The diameter of the upper shaft is d = 20 mm. Determine the normal stress at point B, which is located on the surface of the upper shaft at the y0 axis.
ANSWERCD
The handwheel shown consists of the shaft, flange, and handle. A force P = 1 kN is applied to the handle as shown. The dimensions a and b are 110 mm and 220 mm respectively. If the diameter of the shaft is 24 mm, determine the maximum normal and shearing stress in the shaft. FLANGE a SHAFT HANDLE
25 kN 25 KN 12 mm 18 mm 1.55 The lap joint is fastened with four 3/4-in.-diameter rivets. The working stresses are 14 ksi for the rivets in shear and 18 ksi for the plates in bearing. Find the maximum safe axial load P that can be applied to the joint. Assume that the load is equally distributed among the rivets. 7.5 mm 25 KN 7.5 mm 4 in. in. 25 KN 12 mm 12.5 mm FIG. P1.54 18 mm 78 in. FIG. P1.55 78
please answer asap and show complete solutions
A. SOLVE FOR THE STRESS IN THE ROD IF ITS CROSS-SECTIONAL AREA 1S 500mm^2. AVILIV ROD A= 500mm^2 1.5m 3m e=50⁰ P=15KN