Problem 8 A steel bar of thickness h, to be used as a beam, is welded to a vertical support by two fillet welds as shown in the figure. Find the safe bending force F if the allowable shear stress in the welds is rallow. Knowing: b=40mm; c=150mm; d= 60mm; h=5mm; Tallow=130 MPa F

Problem 8 A steel bar of thickness h, to be used as a beam, is welded to a vertical support by two fillet welds as shown in the figure. Find the safe bending force F if the allowable shear stress in the welds is rallow. Knowing: b=40mm; c=150mm; d= 60mm; h=5mm; Tallow=130 MPa F

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A simple pin-connected truss is loaded and supported as shown in the figure. All members of the truss are aluminum pipes that have an outside diameter of 3.00 in. and a wall thickness of 0.210 in. Determine the normal stress in truss member BC. Assume P = 4 kips, Q = 2 kips, a = 5 ft, b = 9 ft, and c = 7 ft. The stresses are positive if tensile and negative if compressive. Answer in ksi rounded-off to 2 decimal places. P e (3) B b T Gra a Adc Ref you
A pressurized cylindrical container, as in the figure, is made of 12 mm thick plate as shown in the figure. The pressure in the cylinder is given as 1400 kPa and axial load F = 70 kN. According to the cylinder's inner D = 1.5 m; Find the normal stress and shear stress occurring along the welding seams in the cylinder. kaynak dikiş düzlemi = weld bead surface
A cylindrical tank with hemispherical heads is constructed of steel sections that are welded circumferentially (see figure). The tank diameter is 1.1 m, the wall thickness is 32 mm, and the internal pressure is 12 MPa. Determine the maximum shear stress in the cylindrical tank. Welded seams Lutfen birini seçin 8.75.89 MPa b. 62 50 MPa C. None d. 22.67 MPa e 103 13 MPa
2 kip/ft 6 in 10 in B. 40 kip 16 in D. 16 In 5 ft 5 ft 10 ft The simply-supported beam-column above is subjected to a uniformly distributed load and an axial load, as shown. Assume that the Internal resultants on the cross-section passing through point D are as follows: • ND -40 kip • VD 0 Mp = +100 kip-ft Which of the following is closest to the longitudinal normal stress at point D? O-78.1 psi +235 psi O-153 psi O-1.77 ksi H:
10.5 (B) A compound tube of 300 mm external and 100 mm internal diameter is formed by shrinking one cylinder on to another, the common diameter being 200 mm. If the maximum hoop tensile stress induced in the outer cylinder is 90 MN/m² find the hoop stresses at the inner and outer diameters of both cylinders and show by means of a sketch how these stresses vary with the radius. [90, 55.35,-924, 57.8 MN/m²]
The figure shows a horizontal steel bar of thickness h loaded in steady tension and welded to a vertical support. Find the load Fthat will cause an allowable shear stress, Tallow, in the throats of the welds. # h b = 51 mm, d = 49 mm, h = 4.7mm, and Tallow = 140 MPa The load F that will cause an allowable shear stress in the throats of the welds is kN.
For the beam shown: Find the maximum possible principal stresses at points C and D on the cross section shown. Data are as follows: P= 6.2 kN, L= 3.2 m, d = 1.25 m, b = 80 mm, t= 25 mm, h = 120 mm, and h, = 90 mm. h B
EV A steel bar of thickness h, to be used as a beam, is welded to a vertical support by two fillet welds as shown in the figure. Find the safe bending force Fif the allowable shear stress in the welds is 140 MPa. h = 5 mm; b= d = 50 mm; G and c = = 150 mm الملك ايه 100 h LI F
Handwritten solution
A welded steel girder having the cross section shown in the figure is fabricated of two b-180 mm*tf25 mm flange plates and a h=600 mm*tw3D15 mm web plate. The plates are joined by four fillet welds that run continuously for the length of the girder (1=1.15x10° mm“). Each weld has an allowable load in shear of 810 kN/m. Calculate the maximum allowable shear force Vmax for the girder. tw Lutfen birini seçin a. 1.32 MN b. 1.31 MN