Prob 7. Steady - state creep data taken for stainless steel at a stress level of 70 MPa (10,000 psi) are given as follows: (8 marks) If it is known that the value of the stress exponent n for this alloy is 7.0, compute the steady - state creep rate at 1250 K and a stress level of 50 Mpa. é, (s-1) T (K) 1.0 X 10-5 2.5 X 10-3 977 1089

Prob 7. Steady - state creep data taken for stainless steel at a stress level of 70 MPa (10,000 psi) are given as follows: (8 marks) If it is known that the value of the stress exponent n for this alloy is 7.0, compute the steady - state creep rate at 1250 K and a stress level of 50 Mpa. é, (s-1) T (K) 1.0 X 10-5 2.5 X 10-3 977 1089

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Ductility (%EL) 70 60 50 40 30 20 10 Brass 1040 Steel 10 Copper 20 30 40 50 Percent cold work 60 70 Percent cold work = 0 Ductility = 0
Identify the main properties trend (grain size, ductility, strength, hardness) of metal alloys as a percent of cold work on the diagram below.
Compute the elastic modulus for the following metal alloys, whose stress-strain behaviors may be observed in the "Tensile Tests" module of Virtual Materials Science and Engineering (VMSE): (a) titanium, (b) tempered steel, (c) aluminum, and (d) carbon steel. How do these values compare with those presented in Table 6.1 for the same metals? Part 1 a) What is the elastic modulus of titanium in GPa using the data from VMSE? b) What is the elastic modulus of titanium in GPa from Table 6.1? a) E= i GPa b) E= i GPa eTextbook and Media Save for Later Attempts: 0 of 5 used Submit Answer
i need the answer quickly
5. Derive expressions for a simple Voigt element in the following experiments: (a) Creep experiment: time-dependent compliance, J(t) (b) Stress-relaxation experiment: time-dependent modulus, E(t) (c) Constant extension rate experiment: change in stress, o(t)
Problem 5 High-strength stainless steel is required for use in building structures and equipment (e.g. , cranes). It is produced by heat treating quench-hardened steel in a process called tempering that reduces brittleness and imparts toughness. In a production facility, alloy steel plates (k=50 W/(m K), c=460 J/(kg K) and p=7865 kg/m³) of thickness 3 cm have to be tempered in a convective oven by heating them to 550°C. If the plates are initially at 40°C and the air inside the heat treating oven is at 700°C with a convective heat transfer coefficient of 45 W/(m? K), determine how long the plate has to remain in the oven.
kindly help me with this problem choose the correct answer
4) In the temperature range from 600°C to 750°C, a steel wire with 100 mm length shows the steady state creep behavior. The wire was exposed to 600°C under 300 MPa for ten years, how long the specimen would be? ( TH Trung Trong Stress (MPa) 1000 FTTinh Tru Trung Trung Trong th 800 600 400 200 100 80 60 40 815 C 20 d 10-6 104 10-5 650 C 730 C 925°C d d d d d 10-3 10-2 10-1 1 10 10² Steady-state creep rate (h-¹) 10³
Parvinbhai
the behaviour of graphite materials under stress
In the Figure below, the tensile breaking strength, (sigma mark)tenstile-breaking = 140 ??? breaking strength at compression (sigma mar)kcompression-breaking = 460 ??? pouring Machine part made of iron is shown. to the piece P=25 kN forces are acting. piece for t=26 mm Calculate reliability according to Coulomb - Mohr theory ?
Draw the systematic diagram