For the aluminum alloy whose stress-strain behavior can be observed in the "Tensile Tests" module of Virtual Materials Science and Engineering (VMSE), determine the following: (a) the approximate yield strength (0.002 strain offset), i MPа (b) the tensile strength, and i MPa (c) the approximate ductility, in percent elongation. i %EL

For the aluminum alloy whose stress-strain behavior can be observed in the "Tensile Tests" module of Virtual Materials Science and Engineering (VMSE), determine the following: (a) the approximate yield strength (0.002 strain offset), i MPа (b) the tensile strength, and i MPa (c) the approximate ductility, in percent elongation. i %EL

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Match the image with the material property depicted by the image. - 1.…

A: Ductile failure or fracture: When the tensile stress increase in a ductile material than it behaves…

Q: In an engineering application, the material is a strip of iron with a fixed crystallographic…

A: Given: The yield strength of material for grain size of 30 microns, σ₁ = 110 MPa The yield strength…

Q: SHORT ANSWER Use the stress-strain figure below to answer the following questions: 1) In the…

A: The given graph in the question is the stress-strain diagram- There are various points in a…

Q: aluminum alloy 2014

A: Problem asked to specify a practical heat treatment for a 2014 aluminum alloy that will produce a…

Q: Steady-state creep rate data are given here for some alloy taken at 200°C (473 K): i Es (h-¹) 2.2 x…

Q: 1. Two iron samples with different grain sizes are tensile tested. The grain size of sample A is…

A: The size of grain A and B is 1.1 and 0.37 μm respectively.

Q: Computational analysis has determined that a particular design of glass ceramic component has a…

Q: Q1. A tower crane is used to lift I beams to construct skyscraper. As shown in Figure Q1 (a), the…

A: When elastic cables are subjected to tensile force it tends to extend and this elongation per unit…

Q: Calculate the activation energy in j/mol for the creep of an alloy having the steady state creep…

Q: Determine the material p Material Property Data (v Material: Carbon Steel C Property: %Elongation a

A: Given: Material: Carbon Steel C1018 (AISI 1018) Hot Rolled Diameter: 1 in So, from design data book…

Q: Larger animals have sturdier bones that smaller animals. A mouse’s skeleton is only a few percent of…

A: Given data: Mass of man = 70 kg Cross-sectional area of femur = 4.8 x 10-4 m2 Compressive strength…

Q: Steady-state creep rate data are given here for some alloy taken at 200°C (473 K): i, (h) a (MPa)…

A: Find the steady state creep rate .

Q: You need to produce a Ci-Ni alloy having minimum yield strength of 20,000psi, a minimum tensile…

A: Required properties for Cu-Ni alloy:Minimum yield strength (σy) = 20,000 psiMinimum tensile strength…

Q: The properties of the constituents of a unidirectional composite prepreg material are given in table…

A: The quasi-isotropic layup is designed to provide the laminate with isotropic properties in all…

Q: Determine the material property of the materials from the following website. Material Property Data…

A: The mild and hot-rolled steel ASTM A36 is the most widely utilised. It is appropriate for grinding,…

Q: 4. The mechanical properties of a given titanium alloy (Ti-6Al-4V) are E = 114 GPa, σy = 880 MPa and…

Q: Sintered silicon nitride parts are expected to experience tensile stresses 50% of the ultimate…

A: Given data:- tensile stresses (σ) =50% of the ultimate tensile strength Specific surface energy (γ)=…

Q: Based on the stress-strain plots, which materials tested are stiff and which are tough? How can you…

A: Solution:

Q: Current Attempt in Progress Consider 6.8 kg of austenite containing 0.43 wt% C, cooled to below…

Q: Material Proper Material: Carbo Property: Ultim 49,900

A: Given; Material: Carbon Steel C1045 (AISI 1045) Cold Drawn Diameter: 1 inch

Q: You are given three metal test samples, with the same chemical composition and differing grain…

Q: For the stress-strain curve shown below, please estimate the properties indicated. Please do your…

A: Given:Stress-Strain curve.To find:Various mechanical properties enlisted.

Q: The properties of a titanium allow used in commercial airplanes are shown in the table: Grain Size…

A: (a) The general equation of the Hall-Petch equation is, σy=σi+K·d-12 where σi and K are the…

Q: Figure QI(a) shows the stress-strain graphs of four dıfferent materials labelled as A, B, C and D.…

A: a) The order of strain hardening in the material ABCD is as below. A> C >B >D b) Proof…

Q: The yield strength for an alloy that has an average grain diameter of 4.6 x 102 mm is 112 MPa. At a…

Q: How did temperature affect the toughness of the specimens?

A: temperature affecting the strengths of the toughness . IMPACT TOUGHNESS Toughness is the area…

Q: The engineering yield strength of an alloy is 80 ksi. If the modulus of elasticity for this alloy is…

A: (a) let suppose the yield strength of the alloy is 23.9 ksi instead of 80 ksi ( σ=E∑23.9 x…

Q: In order to find out the effects of the grain sizes on the mechanical strength of a metal, three…

A: Given data:

Q: You have been asked to draw up a specification for a ceramic cladding tile that is likely to…

Q: he behaviour of graphite materials under stress

A: The behavior of graphite materials under stress is influenced by their unique atomic structure and…

Concept explainers

Nanomaterials and Applications

Nanomaterials are materials that are composed of nanoparticles having a size ranging from 1 to 100 nm. The constituent particles are 100,000 times smaller than the thickness of a strand of human hair. The nanoparticles cannot be seen through naked eyes and require very high-resolution microscopes. Here, 'nm' stands for nanometer. These materials can occur naturally or can be artificially made. Artificially made nanomaterials are often called lab-engineered nanomaterials. Nanomaterials are extensively used in electronics, medical, aerospace, and other industries.

Question

100%

For the aluminum alloy whose stress-strain behavior can be observed in the "Tensile Tests" module of Virtual Materials Science and
Engineering (VMSE), determine the following:
(a) the approximate yield strength (0.002 strain offset),
MPa
(b) the tensile strength, and
i
MPa
(c) the approximate ductility, in percent elongation.
i
%EL

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The yield strength for an alloy that has an average grain diameter of 5.9 x 10-2 mm is 148 MPa. At a grain diameter of 7.8 × 10-³ mm, the yield strength increases to 233 MPa. At what grain diameter, in mm, will the yield strength be 247 MPa? d = i mm
Based on these results, which material would be better to use for constructing an earthquake-resistant structure? Explain.
The yield strength for an alloy that has an average grain diameter of 5.2 x 102 mm is 110 MPa. At a grain diameter of 6.3 x 103 mm, the yield strength increases to 251 MPa. At what grain diameter, in mm, will the yield strength be 222 MPa? d = mm
A component made of 7075-T6 aluminum alloy has an edge crack of 1.4 mm in length. Plane strain fracture toughness of this alloy is given as 27 MPavm. Geometrical factor of the crack is given as 1.2. (a) If this alloy is subjected to uniaxial tensile stress of 380 MPa, determine whether sudden brittle fracture occurs or not. (b) Calculate the maximum allowable crack size for this component in order not to be failed in brittle manner under a stress of 1000 MPa (Density of steel 7.85 g/cm³, 9.80665 N = 1 kg). Modulus of elastisity, GPa Ultimate tensile Yield strength, Alloy strength, MPa MPa 2014 Al alloy Bronze (92Cu-8Sn) High carbon steel Pure Titanium 97 186 380 72 110 152 380 615 215 240 330 107
1. Suppose that you have measured the strain aging kinetics of a high-strength low-alloy (HSLA) steel and obtained the following results: Aging Temperature (°C) Aging Time (min) ΔΥ (MPa) 150 240 40 130 1800 40 Determine (using a mathematical rather than graphical approach) the time necessary to obtain a strengthening increment, AY, of 40 MPa at an ageing temperature of 120°C. State any assumptions made in order to arrive at your approximation.
The yield strength for an alloy that has an average grain diameter of 4.6 x 10-2 mm is 105 MPa. At a grain diameter of 7.7 × 103 mm, the yield strength increases to 248 MPa. At what grain diameter, in mm, will the yield strength be 234 MPa? d = i mm
(b) A cylindrical rod made from an unknown metal is 350mm long and has a diameter of 10mm. The rod is subjected to a tensile load. It experiences only elastic deformation and elongates by less than 1.0mm under an applied load of 19,800N. Could any of the four metals listed in the table below could be the unknown metal? If so which ones and why? Material Modulus of Yield Ultimate Elasticity / GPa Strength / MPa Tensile Strength / MPa Aluminium 70 255 420 alloy Brass 100 345 420 Copper alloy Steel 110 250 290 207 450 550
Calculate the ductility of this steel alloy in %EL.
In an engineering application, the material is a strip of iron with a fixed crystallographic structure subject to a tensile load during operation. The part failed (yielded) during operation and needs to be replaced with a component with better properties. You are told that two other iron strips had failed at yield stresses of 110 and 120 MPa, with grain sizes of 30 microns and 25 microns respectively. The current strip has a grain size of 20 microns. The diameter of the rod is 1 mm and the load applied is 100 N. What is the yield stress of the new part C and would you recommend it for operation? Select one: a. O b. 129.5, yes C. 133.5 MPa, yes e. 120.5 MPa, no d. 140.5, no 123.5 MPa, yes
Determine the tensile strength, yield strength and percentage elongation (% ductility) for an iron- carbon alloy with 0.76 wt % carbon composition. O Yield strength - 60000 psi : Tensile strength - 110000 psi: Ductility - 15% O Yield strength - 130000 psi : Tensile strength - 68000 psi;: Ductility - 10% O Yield strength - 68000 psi : Tensile strength - 130000 psi; Ductility - 10% O Yield strength 50000 psi: Tensile strength - 100000 psi: Ductility - 20% O Yield strength - 86000 psi : Tensile strength 150000 psi: Ductility 25%
One.