Question 6Horizontal force P = 600 N magnitude applied to end D of lever ABD. Find(a) normal and shearing stresses on element at H having sides parallel to xand y axes(b) principal planes and principal stresses at H.P= 600 NВT= 270 N.m.450 mm250 mmD30 mmM, = 150 N.m100 mmFind equivalent force-couple system at= 56.6 MPacenter of transverse section passingthrough H.P = 600 NT = (600 NX0.45 m)= 270 NmM, = (600 N)0.25 m)=150 Nm50.9 MPaTryFind normal and shearing stresses at H.(150 Nm X0.015 m)+z (0.015m)"(270 Nm)X0.015 m)}7(0.015 m)"Mc6, =+Te=+o, = +56.6 MPaT, = +50.9 MPa

Answered: Image /qna-images/answer/b2578a2b-b626-4469-8f80-e264c9ecc102.jpg

prizontal force P = 600 N magnitude applied to end D of lever ABD. Find ) normal and shearing stresses on element at H having sides parallel to x and y axes O Rrincipal planes and principal stresses at H. P= 600 N T- 270 N.m. 450 mm 250 mm 30 mm M, - 150 N.m 100 mm Find equivalent force-couple system at center of transverse section passing 56.6 MPa through H. P= 600 N T = (600 NX0.45 m)= 270 Nm M, = (600 N)X0.25 m)=150 Nm 50.9 MPa Find normal and shearing stresses at H. (150 NmX0.015m) 7(0.015m) (270 NmX0.015m) (0.015 m)" Me Te o, =0 o, = +56.6 MPa r, =+50.9 MPa

prizontal force P = 600 N magnitude applied to end D of lever ABD. Find ) normal and shearing stresses on element at H having sides parallel to x and y axes O Rrincipal planes and principal stresses at H. P= 600 N T- 270 N.m. 450 mm 250 mm 30 mm M, - 150 N.m 100 mm Find equivalent force-couple system at center of transverse section passing 56.6 MPa through H. P= 600 N T = (600 NX0.45 m)= 270 Nm M, = (600 N)X0.25 m)=150 Nm 50.9 MPa Find normal and shearing stresses at H. (150 NmX0.015m) 7(0.015m) (270 NmX0.015m) (0.015 m)" Me Te o, =0 o, = +56.6 MPa r, =+50.9 MPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The rigid element BCD is supported by a bar AB with a diameter of 25 mm and a connection at C with a diameter of 10 mm. Determine:a. The normal stress in bar AB. b. The shear stress of the bolt at C.
asap please thank you
For the beam and loading shown, consider the n-n section. (a) Absolute value of shear force in n-n section |V| In kN units, (b) the absolute value of the shear stress at point a of the n-n section |τ| Specify in MPa units. Take the P value of 34 kN and the D value of 17 mm in the question.
Determine the force in member IB. 100 kN H K F AC B. O Cannot be identified 0 150 kN O O KN O 50 kN O 100 kN
Determine the principal stresses and the absolute maximum shear stress developed at point A of the sectiontransverse a–a of the support below.
The five 20mm-diameter rivets fasten the plate as shown in the figure to the fixed member. a). Determine the value of the load P so that the average stress of any rivet does not exceed 80MPa.b). What additional clockwise torque can be applied before the shearing stress exceeds 90MPa
3. Determine the required diameter of the pins at A and B to the nearest 1mm if the allowable shear stress for the material is T= 300 MPa. Pin A is subjected to doble shear, whereas pin B is subjected to single shear. A 1.5 m B 1.5 m C D 30 kN 2.25m
5-83 The A-36 steel shaft is made from two segments: AC has a diameter of 0.5 in. and CB has a diameter of 1 in. If the shaft is fixed at its ends A and B and subjected to a uni- form distributed torque of 60 lb in./in. along segment CB, determine the absolute maximum shear stress in the shaft. 5 in. 0.5 in. 20 in. 60 lb-in./in. 1 in. B Prob. 5-83
Part 4a)Determine the reaction (in N) at the hinge at C.b) Determine the diameter of the pin at C in mm.c) Determine the corresponding bearing stress in the pedal at C in MPa.
- Determine the force in member GH and state if the member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. FGH = Submit Part B. FBC= μA Value Part C Request Answer Determine the force in member BC and state if the member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. HA Value Submit Request Answer 3 μA Units FBG = Value → Units ? Determine the force in member BG and state if the member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. Units ? ?
Calculate the maximum moment (with diagram) & maximum shear (with diagram)
F5. The circular shaft AC is fixed to rigid walls at A and C. The section AB is solid annealed bronze and the hollow section BC is made of aluminum alloy 2024 T-4. There is no stress in the shaft before the 20,000 ft-lb torque is applied. Determine the maximum shearing stress in each shaft after T is applied. Section BC 4 D=4" 20 ft-k 6.5-FE B 5ft Match each item to a choice: TAB TBC 2"