Preliminary sizing of a rectangular RC beam has determined that it should have effective depth d=386mm, main (flexural reinforcement) bar diameter p=25mm, shear reinforcement bar diameter '=8mm and cover to outermostreinforcement c_min=50mm. Calculate the total depth of the beam section, h, to the nearest millimetre.

Given: d = 386 mm Main rebar = 25 mm dia. sittups = 8 mm dia cover = 50 mm

Answered: Preliminary sizing of a rectangular RC…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

In the design of beam for the limit state of collapse in flexure as per IS 456 : 2000, let the maximum strain in concrete be limited to 0.0030 (in place of 0.0035) for this situation consider a rectangular beam section of width 300 mm, effective depth as 400 mm, area of tension steel used is 900 mm2. Material used is M20 concrete mix Fe415 grade steel (a) Limiting depth of neutral axis (b) Actual depth of neutral axis
Answer the following for the section at Point D Only Calculate the distributed load "w" that: Will cause the section crack Will cause the reinforcement to yield. Material Properties: F'c = 5000 psi Fy = 60000 psi Es = 29000000 psi Ln = 27 ft L wl₂² 16 wl,² 14 CD L wl,2 vl₁² 10 11 win² 16 h: 28 in A=4 in² b=14 in n d: 25 in
a simply supported beam 300mm wide, 500mm deep and spans 5.7m supports a service super imposed dead load of 8kN/m and service live load of 7kN/m. concrete strength f'c=21MPa and steel yield strength fy=415MPa. concrete cover to bar centroid is 70mm. determine the required amount of tensile reinforcement in mm^2 as per provisions of NSCP 2015.
I need a solution quickly, Use ACI Code
7. For a beam of cross-section, width = 230 mm and effective depth = 500 mm, the number of rebars of 12 mm diameter required to satisfy minimum tension reinforcement requirement specified by IS: 456-2000 (assuming grade of steel reinforcement as Fe500) is mi
Given the concrete (f c=6000 psi) I-beam shown in Figure 1 for the given loading: -draw the shear & moment diagrams -determine Vmax & Mmax -using ASD (Allowable Stress Design) method, check to see if the given loading produces stresses within the given allowable range (check both Omax & Vmax) Using ACI 318-99, allowable stresses are -for flexure, f = .45f'c -for shear, v. = 1.1√f. (HINTS: 8² -note that the beam is symmetric about both axes -Ix for a triangle is (1/36)bh³+Ad² ) 30 kips 16' 10 kip/ft 22' 20 kips 3'-4' -1-6 -1'-6" Figure 1 1'-
5. The beam shown is reinforced for positive moment with three epoxy-coated #11 bars. The bars terminate at the center of the supports. Neglecting beam weight (concentrated loads are very heavy), determine if the required development length is satisfied. Assume As required = 4.55in², 2 in. clear cover on all sides of the longitudinal reinforcement, normal weight concrete, #3 stirrups @12 in o.c., f'c = 5000 psi and fy = 60,000 psi. 8 ft | Pu 20 ft Pu 8 ft ge2 of 56 30 in b=14in. ed 5/15/2020 As = 3-#11
Problem No. 1A 250x450mm beam witha concrete cover of 40mm and stirrups of 10mm with fc' of 21Mpa and fy of 276Mpa. The reinforcement used has a diameter of 16mm. Calculate the following. 13. Calculate the clear spacing of reinforcements 20 KN/m 15 KN/m 23.889 kN 26.111 kN z (m)
A typical grade beam 300 x 800 is reinforced with 2 - 25M bars and the cover is forconerete cast and permanently exposed to the earth, (f', =30 MPa) Determine the following: (a) the size of the stress block "a" (b) the bending moment “M," (c) the c/d ratio (d) the type of failure (brittle or ductile) based on part (c) (e) check Asmin (equation 2.7) (Code 10.5.1.2) (f) maximum As permitted based on ductile failure (g) determine maximum bar size (2 required) from Table 1.5 based on part f) (h) check spacing requirements 's' Table 2.6 based on part g) (i) check if skin reinforcement is required Table 2.9 and fy = 400mpa please solve asap %3D
A one way simply supported slab of effective length in the shorter span is 3.5 m. Calculate the area of the distribution reinforcement.
4.3 A simply supported beam is reinforced with 5-ϕ25 mm at the bottom and 2-ϕ20 mm at the top of the beam. Concrete covering to centroid of reinforcement is 70 mm at the top and 64 mm at the bottom of the beam. The beam has a gross depth of 450 mm and gross width of 300 mm. fc’= 28 MPa, fy = 415 MPa. Assume bars laid out in single layer. Calculate the following if the limiting tensile steel strain is 0.004 for a ductile failure: Calculate: Maximum service uniform live load over the entire span in addition to a DL = 20 kN/m (including the weight of the beam) if it has a span of 6 m = _____?____ kN/m (to the nearest whole number)

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS