Practice Problem 4.4 (CE Board November 2016) Given: Beam Dimensions, bx h=350mm x 450 mm Effective Cover to centroid of steel reinforcement = 75 mm Concrete Strength, fc=27.5 MPa Steel Strength, fy=415 MPa Stimups, fyv = 275 MPa Shear reduction factor = 0.75 Beam is subjected to shear and flexure only a) The beam is reinforced with 3 legs of 10 mm diameter stirrups space 90 mm on center. Which of the following gives the shear strength of the beam? b) To develop a shear strength of 375 kN, find the spacing of 10 mm diameter stimups consisting of 3 legs. c) Which of the following gives the allowable maximum spacing of 2 legs of 10 mm diameter stimps?

Practice Problem 4.4 (CE Board November 2016) Given: Beam Dimensions, bx h=350mm x 450 mm Effective Cover to centroid of steel reinforcement = 75 mm Concrete Strength, fc=27.5 MPa Steel Strength, fy=415 MPa Stimups, fyv = 275 MPa Shear reduction factor = 0.75 Beam is subjected to shear and flexure only a) The beam is reinforced with 3 legs of 10 mm diameter stirrups space 90 mm on center. Which of the following gives the shear strength of the beam? b) To develop a shear strength of 375 kN, find the spacing of 10 mm diameter stimups consisting of 3 legs. c) Which of the following gives the allowable maximum spacing of 2 legs of 10 mm diameter stimps?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

As a design engineer you are asked to peer review the design done by another engineer at your organization. A typical reinforced concrete floor slab plan is given. Assume all members to be simply supported. The specified compressive strength of concrete is 5000 psi and Grade-60 steel is used. Unit weight of concrete can be assumed as 150 lb/ft³. B 30'-0"- B2 -EQ.- EQ. -EQ. SEC 1 -40'-0" IS B1 B3 B3 B1 2 The only dead load acting on the slab is the self-weight of the members. The live load on the slab is 100 psf. Initial cross-section and reinforcement details of beam B1 is shown. Area of steel is 4.8in². EQ. 40'-0" B EQ. North
Need answer asap. Will surely rate immediately :D The middle of the 5.6 m simple beam has a dimension of 350 mm by 600 mm. On that location, the beam is reinforced with 3-Ø20mm on the top and 7-Ø20 mm at the bottom. The concrete cover to be used is 40 mm. The stirrups used is 12 mm in diameter. The concrete strength of the beam is 27.6 MPa. All reinforcement used is Grade 60 (fy = 420 MPa). The beam is carrying a superimposed dead concentrated load of 55 kN and an unknown superimposed live load both at the midspan. The unit weight of concrete used is 23.6 kN per cubic meter. 1. Determine the distance of the extreme compression from the neutral axis at the correct assumption.2. Determine the unknown concentrated live load that the beam can sustain.3. Determine the design moment capacity of the beam at the midspan.
A simply supported beam 300 mm wide, 500 mm deep and spans 5 m supports a service super imposed dead load of 6 kN/m and service live load of 9 kN/m. Concrete strength f’c = 21 MPa and steel yield strength fy = 415 MPa. Concrete cover to bar centroid is 70 mm. Determine the required amount of tensile reinforcement in mm^2 as per provisions of NSCP 2015. Write your final answer to the nearest whole number.
A rectangular beam has the dimensions (see Figure) b = 12 in., h - 20 in, and d 17 in. and is reinforced with three No. 9 (No. 29) bars so that As - 3.00 in. The concrete compressive strength fe is 4000 psi, and the tensile strength In bending (modulus of rupture) is 475 psi. The yield point of the steel f, is 60,000 psi. Determine the concrete compression stress at the top fiber caused by a bending moment M- 10 ft-kips. 9- 6.78 in, I= 4067 in, Es= 29000000, E = 3600000 17 in. 20 in. 3 #9 bars (A, - 3.00 in.?) 3 in. -12 in- Select one: a. 390 psi b. 1390 psi c. 200 psi d. 250 psi
5. The beam shown is reinforced for positive moment with three epoxy-coated #11 bars. The bars terminate at the center of the supports. Neglecting beam weight (concentrated loads are very heavy), determine if the required development length is satisfied. Assume As required = 4.55in², 2 in. clear cover on all sides of the longitudinal reinforcement, normal weight concrete, #3 stirrups @12 in o.c., f'c = 5000 psi and fy = 60,000 psi. 8 ft | Pu 20 ft Pu 8 ft ge2 of 56 30 in b=14in. ed 5/15/2020 As = 3-#11
Find the minimum theoretical width and height of a rectangular concrete section that will make the beam failure sufficiently ductile. Given: Two layers of 2-Ø25 mm bottom reinforcements fy=414 MPa f'c=35 MPa stirrup diameter=minimum required clear cover=minimum value for beam vertical clear spacing bet. Iayers=minimum value for beam height-to-width ratio=2.0 Note: Ductile failure occurs in beams when the extreme reinforcement layer is strained to 0.004 or greater.
If the given beam section is used for a simply supported beam 5.0 m span, using fc = 21 MPa and fyt = 280 MPa: 10-mm-dia 425 mm @ 200 mm 500 mm -275 mm 75 mm 25. Calculate the nominal shear strength of concrete, using simplified formula of NSCP 2015. = kN 26. Calculate the nominal shear strength of the stirrups, Vg = kN. 27. Calculate the design sectional shear strength of the beam = kN 28. Determine the maximum factored uniform load in that can be sustained based on shear strength of the cross-section only. = kN/m 29. Determine the maximum live load in that can be sustained based on shear strength of the cross-section only. = kN/m 30. If the total factored uniform load is 60 kN/m, calculate the ultimate shear force at critical section for shear in kN. = kN INPUT ALL ANSWERS ROUNDED TO WHOLE NUMBER
Find the ultimate moment of resistance for the rectangular section reinforced as shown below. material strengths: Concrete Reinforcement Width of section Reinforcement fcu= 30-MPa fy:= 450-MPa b:= 280 mm d:= 510 mm d':= 50-mm 2 A, 2410-mm A's:= 628-mm 2 b A', Hi As
A simply supported beam 300 mm wide, 500 mm deep and spans 5.5 m supports a service super imposed dead load of 8 kN/m and service live load of 9 kN/m. Concrete strength f’c = 21 MPa and steel yield strength fy = 415 MPa. Concrete cover to bar centroid is 70 mm. Determine the required amount of tensile reinforcement in mm^2 as per provisions of NSCP 2015. Write your final answer to the nearest whole number.
Compute the design strength of a doubly reinforced beam given the following data: Beam width: 420 mm Effective depth: 590 mm As: 6-28 mm dia. bars As’: 3-20 mm dia. bars Steel yield strength: 345 MPa Concrete strength: 20.7 MPa Clear cover of top bars up to main compressive reinforcement: 50 mm
1. A two span beam subjected to shear and flexure only is reinforced as follows: SECTION: TOP BARS @ MIDSPAN: 2-⌀20mm @ FACE OF SUPPORTS: 5-⌀20mm SECTION: BOTTOM BARS @ MIDSPAN: 3-⌀20 mm @ FACE IF SUPPORTS: 2-⌀20 mm Given: Stirrup diameter, ds = 10 mm Concrete f'c = 21 MPa Steel rebar fy = 415 MPa Stirrup fy = 275 MPa Beam size b x h = 270 mm x 450 mm Assume all bars laid out in single layer. Calculate the following: a. Design Moment strength of section at midspan for positive bending = ______ kN·m (nearest whole number)
What is the steel reinforcement index of a concrete beam with 351 mm width, 536 mm depth, and 6- ø21 mm bars? The yield strength of its reinforcement is 371 MPa and the specified compressive of concrete is 28 MPa.